MINWAX® Technical Data Sheet
MINWAX® PRE-STAIN WOOD CONDITIONER
DESCRIPTION:_____________________________________
Minwax® Pre-Stain Wood Conditioner is specically designed for use before staining new or bare softwood
surfaces. It penetrates the grain of the wood to promote uniform acceptance of stain. Wood Conditioner pen-
etrates the pores of the wood, reducing the amount of stain the larger pores will absorb. This evens out the
absorption of stain, greatly reducing streaking and blotching.
RECOMMENDED USE:__________________________________
Designed for use on any soft or porous wood surface - Common examples include pine, r, and spruce (soft) or
maple, alder and aspen (porous).
To determine if you are working with softwood, press your ngernail against a hidden section of the wood. If
your nail leaves an impression or dent in the wood consider using the Pre-Stain Wood Conditioner. Pre-Stain
should be used to avoid an uneven stain color. Pre-Stain Wood Conditioner may be used on all wood types but
may limit or reduce the overall stain color on hard woods and less porous wood types.
SURFACE PREPARATION:________________________________
Use on clean, raw wood surface. Remove all dust and debris using a soft cloth dampened with mineral spirits.
APPLICATION NOTES:___________________________________
1) Apply the Pre-Stain Wood Conditioner before staining on clean, raw wood, using a brush or cloth.
2) Allow the Wood Conditioner to penetrate 5-15 minutes, and then remove excess Conditioner with a
clean dry cloth.
3) The stain should be applied
within two hours of application of Pre-Stain Wood Conditioner. For best
results, stain with Minwax Wood Finish, Minwax Gel Stain, Minwax Polyshades, or Minwax WoodSheen.
Note: Minwax® Pre-Stain Wood Conditioner is not recommended for use with water-based stains. For the Min-
wax Water-Based Stains, pretreat wood with the Minwax Water-Based Pre-Stain Wood Conditioner.
Note: For long-lasting protection, complete your project with Minwax Fast-Drying Polyurethane, Minwax
Polycrylic, or another ne Minwax protective clear nish.
Note: When using alder wood, it is recommended to let the Pre-Stain Wood Conditioner set for 2 hours before
staining.
PRECAUTIONS: Do not allow Minwax Pre-Stain Wood Conditioner to dry before staining. This will mini-
mize the wood texture and/or grain pattern as well as limiting the overall stain color penetration.
CLEANUP/STORAGE:__________________________________
Use mineral spirits, paint thinner or turpentine. Do not store near heat, sparks, open ame or other sources of
ignition. Close container after each use. Store only in original container. Keep out of reach of children.
12/06
SAFETY:_________________________________________
*Read all label directions and cautions carefully before use*.
CAUTIONS: Contents are COMBUSTIBLE. Keep away from heat and open ame. Prevent buildup of vapors
by using cross ventilation. CONTAINS: ALIPHATIC HYDROCARBONS. VAPOR HARMFUL. MAY
AFFECT THE BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR NAUSEA.
CAUSES EYE, SKIN, NOSE AND THROAT IRRITATION. Use only with adequate ventilation. To avoid
overexposure, open windows and doors or use other means to ensure fresh air entry during application and dry-
ing. If you experience eye watering, headaches, or dizziness, increase fresh air, or wear respiratory protection
(NIOSH approved) or leave the area. Avoid contact with eyes and skin. Wash hands after using. Keep con-
tainer closed when not in use. Do not transfer contents to other containers for storage. HARMFUL IF SWAL-
LOWED. If swallowed do not include vomiting. Get medical attention immediately. FIRST AID: In case of
eye contact, ush thoroughly with large amounts of water for 15 minutes and get medical attention. For skin
contact, wash thoroughly with soap and water. In case of respiratory difculty, provide fresh air and call physi-
cian. DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents, which can cause
permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the
contents can be harmful or fatal. KEEP OUT OF REACH OF CHILDREN. CONFORMS TO ASTM D-
4236. Contact a physician for more health information.
PHYSICAL PROPERTIES:_______________________________
Testing method:
Resin type: Modied Linseed Oil/Hydrocarbon Resin
Solvent: Mineral spirits
Odor: Mild hydrocarbon
No. of coats: 1 - Additional coats may be applied on highly absorbent woods
Dry-time: 15 Minutes
Stain application: After 15 minutes but no more than 2 hours
Flash point: >101 Fahrenheit SETAFLASH*
Applicator: Brush or cloth
VOC (grams/liter): 350
Coverage (sq. ft./gal.): 500
% Solids: 10.24 +/- .5 ASTM D 2369
Specic gravity: .796 +/- .005 ASTM D 2369
Pounds/gallon: 5.85
Viscosity (centipose): 50cps ASTM D 2196
*SETAFLASH is a registered trademark of Stanhope-Seta Limited.
12/06
