TOSHIBA MACHINE
PANTONE 193
TOSHIBA MACHINE
CMYK
TOSHIBA MACHINE
K
TOSHIBA MACHINE
WHITE
U.S.A. Specifications - Catalog #ECSX 3-15
SPECIFICATIONS
*Specifications are subject to change without notice
Maximum injection and holding pressure are valued by the power of injection unit, not resin pressure.
Maximum injection and holding pressure are limited according to molding conditions.
...but it is so versatile, with a greater range of shot
sizes, you’ll think it was triplets.
It’s the new SX all-electric...packed with new and enhanced
features that give you extraordinary quality and unsurpassed
flexibility.
20% improvement in your dry cycle times
The new SX’s friction-reducing linear bearing ways and
dynamic acceleration/deceleration control give you signifi-
cantly faster cycle times.
Extending your mold life
Its shockless acceleration/deceleration programming helps
reduce wear and tear on your mold, minimizing mold
maintenance and maximizing mold life.
Minimizing part contamination
Bushing-free, grease-free tie bars reduce the possibility of
contaminating molded parts.
Uniform clamping
force across mold
surface
The new SX features
a 5-point “Linkline”
toggle mechanism
that directs pressure
to the center of the
mold surface. As a
result, you achieve
uniform clamping force
across the entire mold
surface, improving
quality and minimizing
defect rates.
With uniform mold surface pressure, you can recycle
tonnage, enabling you to maximize mold life and minimize
machine maintenance.
More shot sizes with a single machine
With the SX, you get a wider range of barrel choices from
a single machine, enabling you to shorten changeover
times and move from project to project, quickly and easily.
As a result, you can be more competitive on new jobs and
increase your shop’s flexibility without investing in new
equipment. And with quicker changeovers, you can be
online and molding faster than ever before.
S
3
- Simple, Steady, Smooth
The Friction-Free Drive on the SX injection unit ensures
more accurate injection speed and back pressure control,
improving shot-to-shot repeatability throughout the pro-
cessing cycle.
This may look like
one machine...
Left, uneven pressure. Right,
improved uniform clamping force.
5-point Linkline mechanism for
more uniform clamping force.
©2015 Toshiba Machine, Inc.
Friction-Free
injection drive.
V50 Controller uses Real-Time Information
With a 40% improvement in communication speed, the
new V50 controller on the SX uses real-time input to report
molding conditions and make automatic adjustments to
mold settings. This results in greater part repeatability and
fewer rejects.
User customization
The V50’s intuitive, touch-
screen interface enables
you to customize machine
cells without investing in ad-
ditional OEM programming.
Up to 40 user-programma-
ble outputs are available.
Monitoring and program-
ming are easy, thanks to a
large 15-inch touch screen.
And since screens look and
work the same as previous
controllers, there’s little or
no learning curve for current users. Just a single call to
Toshiba gets you answers to your programming questions.
In addition, the V50 includes “iPAQET Lite” data
management software. A significant value-added benefit,
it enhances your investment by providing you with produc-
tion monitoring, data collection and analysis, and more.
iPAQET Remote Monitoring
and Management Software
(Optional)
A valuable upgrade to “iPAQET Lite,” the full version of
“iPAQET” offers a more powerful data management plat-
form. Monitor up to 48 molding machines from anywhere,
in REAL TIME. iPaqet provides you with production mon-
itoring, data collection and analysis, machine operation
status, resin lot monitoring and more.
Let the machine think for you
Clamping force dynamic self-tuning (DST-PRESS):
As an option setting, you can allow tie-bar strain sensors to
automatically adjust clamping force based on direct feed-
back of changing molding conditions such as increased
heat and expansion.) This results is more consistent pro-
cessing from shot to shot throughout the processing cycle.
Injection process condition dynamic self-tuning (DST-FILL):
You can further increase shot consistency by allowing the
machine to automatically change barrel temperatures
and transfer points to compensate for material viscosity
fluctuations.
Additional molding control software
Virtual Hydraulic Injection (H1) circuit - Replicates the hy-
draulic cascade effect to create more even flow rates into
mold cavities. High sensitivity 3-stage mold protection -
Puts the machine into mold safety/shut down when torque
settings are exceeded during mold clamping. Ejector
torque monitor - Helps prevent tool and part damage.
Ask your Toshiba representative for a complete list of
standard and optional software.
Note 1: When using iPAQET, an Ethernet interface (standard) is required
on the injection molding machine itself.
Note 2: All server, server peripherals and operating systems, and
LAN wiring are separately required for iPAQET.
...but its shot
range says more
ITEM UNIT EC30SX EC55SX EC85SX EC110SX EC110SX EC140SX EC200SX
CLAMP
Clamp force
tf 30 50 75 100 100 130 180
US Ton 33 55.1 82.7 110.2 110.2 143.3 198.4
Tie bar
distance
H x V mm 320 x 290 410 x 360 410 x 360 460 x 410
460 x 410 510 x 460 560 x 510
H x V in 12.6 x 11.4 16.1 x 14.2 16.1 x 14.2 18.1 x 16.1 18.1 x 16.1 20.1 x 18.1 22.0 x 20.1
Platen
dimension
H x V mm 440 x 420 510 x 460 580 x 530 660 x 610
660 x 610 720 x 670 790 x 740
H x V in 17.3 x 16.5 20.1 x 18.1 22.8 x 20.9 26.0 x 24.0 26.0 x 24.0 28.3 x 26.4 31.1 x 29.1
Clamp Stroke
mm 230 300 300 350 350 400 450
in 9.06 11.8 11.8 13.8 13.8 15.7 17.7
Maximum daylight
mm 560 770 770 900 900 950 1050
in 22.1 30.3 30.3 35.4 35.4 37.4 41.3
Mold Height
M i n . x M a x mm 150 ~ 330 150 ~ 470 150 ~ 470 180 ~ 550 180 ~ 550 180 ~ 550 200 ~ 600
M i n . x M a x in 5.9 x 13.0 5.9 ~ 18.5 5.9 ~ 18.5 7.1 ~ 21.7 7.1 ~ 21.7 7.0 ~ 21.7 7.9 ~ 23.6
Ejector force
tf 0.8 2 2 3
3 3 5
US Ton 0.88 2.2 2.2 3.3 3.3 3.3 5.5
Ejector Stroke
mm 50 70 70 90 90 90 130
in 1.97 2.8 2.8 3.5 3.5 3.5 5.1
INJECTION
Injection Unit i0.4 i1 U21 U22 U22 U32 U34 U34 U44 U48
Barrel code Y A Y A (1Y) (1A) (1B) (1Y) (1.5Y) (2Y) (2A) (2B) (1Y) (1.5Y) (2Y) (2A) (2B) (2Y) (2A) (2B) (2Y) (2A) (4Y) (4A) (4B) (2Y) (2A) (4Y) (4A) (4B) (4Y) (4A) (4B) (4Y) (6Y) (8Y) (8A) (8B)
Screw Diameter
mm 16 18 22 25 22 25 28 22 25 28 32 36 22 25 28 32 36 28 32 36 28 32 36 40 45 28 32 36 40 45 36 40 45 36 40 45 50 55
in 0.63 0.71 0.87 0.98 0.87 0.98 1.10 0.87 0.98 1.10 1.26 1.42 0.87 0.98 1.10 1.26 1.42 1.10 1.26 1.42 1.10 1.26 1.42 1.57 1.77 1.10 1.26 1.42 1.57 1.77 1.42 1.57 1.77 1.42 1.57 1.77 1.97 2.17
Injection Capacity
cm
3
14 18 38 49 38 49 62 38 55 78 102 130 38 55 78 102 130 78 102 130 78 102 162 201 254 78 102 162 201 254 162 201 254 162 226 318 392 475
in
3
0.85 1.10 2.32 2.99 2.3 3.0 3.8 2.3 3.4 4.8 6.2 7.9 2.3 3.4 4.8 6.2 7.9 4.8 6.2 7.9 4.8 6.2 9.9 12.3 15.5 4.8 6.2 9.9 12.3 15.5 9.9 12.3 15.5 9.9 13.8 19.4 23.9 29.0
Shot Volume
PS
g 13 16 35 45 35 45 57 35 51 72 94 120 35 51 72 94 120 72 94 120 72 94 149 185 234 72 94 149 185 234 149 185 234 149 208 293 361 437
oz 0.46 0.56 1.23 1.59 1.2 1.6 2.0 1.2 1.8 2.5 3.3 4.2 1.2 1.8 2.5 3.3 4.2 2.5 3.3 4.2 2.5 3.3 5.3 6.5 8.3 2.5 3.3 5.3 6.5 8.3 5.3 6.5 8.3 5.3 7.3 10.3 12.7 15.4
PE
g 10 13 28 36 28 36 45 28 40 57 74 95 28 40 57 74 95 57 74 95 57 74 118 147 185 57 74 118 147 185 118 147 185 118 165 232 286 347
oz 0.35 0.46 0.99 1.27 1.0 1.3 1.6 1.0 1.4 2.0 2.6 3.4 1.0 1.4 2.0 2.6 3.4 2.0 2.6 3.4 2.0 2.6 4.2 5.2 6.5 2.0 2.6 4.2 5.2 6.5 4.2 5.2 6.5 4.2 5.8 8.2 10.1 12.2
Maximum Injection
Pressure
MPa 278 220 270 220 284 220 175 284 276 287 220 174 284 276 287 220 174 287 220 174
287 220 247 200 158 287 220 247 200 158 247 200 158 247 253 247 200 165
PSI 40300 31900 39200 31900 41,200 31,900 25,400 41,200 40,00041,60031,900 25,200 41,200 40,000 41,600 31,900 25,20041,60031,900 25,200 41,600 31,900 35,800 29,000 22,900 41,600 31,900 35,800 29,000 22,900 35,800 29,000 22,900 35,800 36,700 35,800 29,000 23,900
Maximum Holding
Pressure
MPa 278 220 270 220 284 220 175 284 276 287 220 174 284 276 287 220 174 287 220 174
287 220 247 200 158 287 220 247 200 158 247 200 158 247 253 247 200 165
PSI 40300 31900 39200 31900 41,200 31,900 25,400 41,200 40,00041,60031,908 25,237 41,200 40,000 41,600 31,900 25,200 41,60031,900 25,200 41,600 31,900 35,800 29,000 22,900 41,600 31,900 35,800 29,000 22,900 35,800 29,000 22,900 35,800 36,700 35,800 29,000 23,900
Injection Rate STD
cm
3
/s 106 134 76 98 76 98 123 76 98 123 161 204 76 98 123 161 204 123 161 204 123 161 204 251 318 123 161 204 251 318 204 251 318 163 201 254 314 380
in
3
/s 6.47 8.18 4.64 5.98 4.6 6.0 7.5 4.6 6.0 7.5 9.8 12.4 4.6 6.0 7.5 9.8 12.4 7.5 9.8 12.4 7.5 9.8 12.4 15.3 19.4 7.5 9.8 12.4 15.3 19.4 12.4 15.3 19.4 9.9 12.3 15.5 19.2 23.2
Injection
Velocity
STD
mm/s 500 200 200 200 200 200
200 200 200 160
in/s 19.7 7.88 7.9 7.9 7.9 7.9 7.9 7.9 7.9 6.3
Injection Rate HIGH
cm
3
/s -
-
190
245
190 245 308 190 245 308 402 509 190 245 308 402 509 308 402 509 216 281 356 440 557 216 281 356 440 557 356 440 557 305 377 477 589 713
in
3
/s -
-
11.6
15.0
11.6 15.0 18.8 11.6 15.0 18.8 24.5 31.1 11.6 15.0 18.8 24.5 31.1 18.8 24.5 31.1 13.2 17.1 21.7 26.8 34.0 13.2 17.1 21.7 26.8 34.0 21.7 26.8 34.0 18.6 23.0 29.1 35.9 43.5
Injection
Velocity
HIGH
mm/s - 500 500 500 500 500
350 350 350 300
in/s - 19.7 19.7 19.7 19.7 19.7 13.8 13.8 13.8 11.8
Plasticizing
capacity
PS
g/sec 2.2 3.3 6.1 7.8 6.1 7.8 9.7 6.1 6.9 11.1 16.9 23.1 6.1 6.9 11.1 16.9 23.1 11.1 16.9 23.1
11.1 16.9 23.1 30.6 33.3 11.1 16.9 23.1 30.6 33.3 23.1 30.6 33.3 18.9 27.2 33.3 44.4 52.8
oz/sec 0.08 0.12 0.22 0.27 0.2 0.3 0.3 0.2 0.2 0.4 0.6 0.8 0.2 0.2 0.4 0.6 0.8 0.4 0.6 0.8 0.4 0.6 0.8 1.1 1.2 0.4 0.6 0.8 1.1 1.2 0.8 1.1 1.2 0.7 1.0 1.2 1.6 1.9
Screw speed RPM 480 480 420 420 420 420 380 420 390 400 390 350 420 390 400 390 350 400 390 350 400 390 350 320 285 400 390 350 320 285 350 320 285 285 285 285 255 230
Nozzle touch force
kN 5.98 5.98 9.8 9.8 9.8 11.8 11.8 11.8 29.4 29.4
US Ton 0.66 0.66 1.1 1.1 1.1 1.3 1.3 1.3 3.3 3.3
GENERAL
Heater Capacity kW 3.4 4.8 4.7 5.4 4.7 5.8 6.8 4.7 5.8 6.8 6.8 6.8 11.2 6.8 11.2 11.2 11.2 13.6 15.2
Machine
Dimensions
L x W x H m 2.9 x 1.0 x 1.6 3.2 x 1.0 x 1.6 4.0 x 1.2 x 1.6 4.0 x 1.2 x 1.6 4.1 x 1.2 x 1.6 4.0 x 1.2 x 1.6 4.1 x 1.2 x 1.6 4.6 x 1.3 x 1.7
4.6 x 1.3 x 1.7 4.9 x 1.3 x 1.7 4.8 x 1.4 x 1.8 4.9 x 1.3 x 1.7 5.2 x 1.4 x 1.8 5.7 x 1.5 x 1.9 5.7 x 1.5 x 1.9 5.9 x 1.5 x 1.9 6.0 x 1.5 x 1.9
L x W x H ft 9.5 x 3.3 x 5.2 10.5 x 3.3 x 5.2 13.2 x 3.9 x 5.2 13.2 x 3.9 x 5.2 13.5 x 3.9 x 5.2 13.2 x 3.9 x 5.2 13.5 x 3.9 x 5.2 15.1 x 4.3 x 5.6 15.1 x 4.3 x 5.6 16.1 x 4.3 x 5.6 15.7 x 4.6 x 5.9 16.7 x 4.6 x 5.9 17.1 x 4.6 x 5.9 18.7 x 4.9 x 6.2 18.7 x 4.9 x 6.2 19.4 x 4.9 x 6.2 19.7 x 4.9 x 6.2
Machine weight
tf 2.0 2.0 3.0 3.2 3.3 4.2 4.2 4.3 5.2 5.3 7.0 7.0 7.3
US Ton 2.2 2.2 3.3 3.5 3.6 4.6 4.6 4.7 5.7 5.8 7.7 7.7 8.0
SPECIFICATIONS
ITEM UNIT EC30SX EC55SX EC85SX EC110SX EC110SX EC140SX EC200SX
CLAMP
Clamp force
tf 30 50 75 100 100 130 180
US Ton 33 55.1 82.7 110.2 110.2 143.3 198.4
Tie bar
distance
H x V mm 320 x 290 410 x 360 410 x 360 460 x 410
460 x 410 510 x 460 560 x 510
H x V in 12.6 x 11.4 16.1 x 14.2 16.1 x 14.2 18.1 x 16.1 18.1 x 16.1 20.1 x 18.1 22.0 x 20.1
Platen
dimension
H x V mm 440 x 420 510 x 460 580 x 530 660 x 610
660 x 610 720 x 670 790 x 740
H x V in 17.3 x 16.5 20.1 x 18.1 22.8 x 20.9 26.0 x 24.0 26.0 x 24.0 28.3 x 26.4 31.1 x 29.1
Clamp Stroke
mm 230 300 300 350 350 400 450
in 9.06 11.8 11.8 13.8 13.8 15.7 17.7
Maximum daylight
mm 560 770 770 900 900 950 1050
in 22.1 30.3 30.3 35.4 35.4 37.4 41.3
Mold Height
M i n . x M a x mm 150 ~ 330 150 ~ 470 150 ~ 470 180 ~ 550 180 ~ 550 180 ~ 550 200 ~ 600
M i n . x M a x in 5.9 x 13.0 5.9 ~ 18.5 5.9 ~ 18.5 7.1 ~ 21.7 7.1 ~ 21.7 7.0 ~ 21.7 7.9 ~ 23.6
Ejector force
tf 0.8 2 2 3
3 3 5
US Ton 0.88 2.2 2.2 3.3 3.3 3.3 5.5
Ejector Stroke
mm 50 70 70 90 90 90 130
in 1.97 2.8 2.8 3.5 3.5 3.5 5.1
INJECTION
Injection Unit i0.4 i1 U21 U22 U22 U32 U34 U34 U44 U48
Barrel code Y A Y A (1Y) (1A) (1B) (1Y) (1.5Y) (2Y) (2A) (2B) (1Y) (1.5Y) (2Y) (2A) (2B) (2Y) (2A) (2B) (2Y) (2A) (4Y) (4A) (4B) (2Y) (2A) (4Y) (4A) (4B) (4Y) (4A) (4B) (4Y) (6Y) (8Y) (8A) (8B)
Screw Diameter
mm 16 18 22 25 22 25 28 22 25 28 32 36 22 25 28 32 36 28 32 36 28 32 36 40 45 28 32 36 40 45 36 40 45 36 40 45 50 55
in 0.63 0.71 0.87 0.98 0.87 0.98 1.10 0.87 0.98 1.10 1.26 1.42 0.87 0.98 1.10 1.26 1.42 1.10 1.26 1.42 1.10 1.26 1.42 1.57 1.77 1.10 1.26 1.42 1.57 1.77 1.42 1.57 1.77 1.42 1.57 1.77 1.97 2.17
Injection Capacity
cm
3
14 18 38 49 38 49 62 38 55 78 102 130 38 55 78 102 130 78 102 130 78 102 162 201 254 78 102 162 201 254 162 201 254 162 226 318 392 475
in
3
0.85 1.10 2.32 2.99 2.3 3.0 3.8 2.3 3.4 4.8 6.2 7.9 2.3 3.4 4.8 6.2 7.9 4.8 6.2 7.9 4.8 6.2 9.9 12.3 15.5 4.8 6.2 9.9 12.3 15.5 9.9 12.3 15.5 9.9 13.8 19.4 23.9 29.0
Shot Volume
PS
g 13 16 35 45 35 45 57 35 51 72 94 120 35 51 72 94 120 72 94 120 72 94 149 185 234 72 94 149 185 234 149 185 234 149 208 293 361 437
oz 0.46 0.56 1.23 1.59 1.2 1.6 2.0 1.2 1.8 2.5 3.3 4.2 1.2 1.8 2.5 3.3 4.2 2.5 3.3 4.2 2.5 3.3 5.3 6.5 8.3 2.5 3.3 5.3 6.5 8.3 5.3 6.5 8.3 5.3 7.3 10.3 12.7 15.4
PE
g 10 13 28 36 28 36 45 28 40 57 74 95 28 40 57 74 95 57 74 95 57 74 118 147 185 57 74 118 147 185 118 147 185 118 165 232 286 347
oz 0.35 0.46 0.99 1.27 1.0 1.3 1.6 1.0 1.4 2.0 2.6 3.4 1.0 1.4 2.0 2.6 3.4 2.0 2.6 3.4 2.0 2.6 4.2 5.2 6.5 2.0 2.6 4.2 5.2 6.5 4.2 5.2 6.5 4.2 5.8 8.2 10.1 12.2
Maximum Injection
Pressure
MPa 278 220 270 220 284 220 175 284 276 287 220 174 284 276 287 220 174 287 220 174
287 220 247 200 158 287 220 247 200 158 247 200 158 247 253 247 200 165
PSI 40300 31900 39200 31900 41,200 31,900 25,400 41,200 40,00041,60031,900 25,200 41,200 40,000 41,600 31,900 25,20041,60031,900 25,200 41,600 31,900 35,800 29,000 22,900 41,600 31,900 35,800 29,000 22,900 35,800 29,000 22,900 35,800 36,700 35,800 29,000 23,900
Maximum Holding
Pressure
MPa 278 220 270 220 284 220 175 284 276 287 220 174 284 276 287 220 174 287 220 174
287 220 247 200 158 287 220 247 200 158 247 200 158 247 253 247 200 165
PSI 40300 31900 39200 31900 41,200 31,900 25,400 41,200 40,00041,60031,908 25,237 41,200 40,000 41,600 31,900 25,200 41,60031,900 25,200 41,600 31,900 35,800 29,000 22,900 41,600 31,900 35,800 29,000 22,900 35,800 29,000 22,900 35,800 36,700 35,800 29,000 23,900
Injection Rate STD
cm
3
/s 106 134 76 98 76 98 123 76 98 123 161 204 76 98 123 161 204 123 161 204 123 161 204 251 318 123 161 204 251 318 204 251 318 163 201 254 314 380
in
3
/s 6.47 8.18 4.64 5.98 4.6 6.0 7.5 4.6 6.0 7.5 9.8 12.4 4.6 6.0 7.5 9.8 12.4 7.5 9.8 12.4 7.5 9.8 12.4 15.3 19.4 7.5 9.8 12.4 15.3 19.4 12.4 15.3 19.4 9.9 12.3 15.5 19.2 23.2
Injection
Velocity
STD
mm/s 500 200 200 200 200 200
200 200 200 160
in/s 19.7 7.88 7.9 7.9 7.9 7.9 7.9 7.9 7.9 6.3
Injection Rate HIGH
cm
3
/s -
-
190
245
190 245 308 190 245 308 402 509 190 245 308 402 509 308 402 509 216 281 356 440 557 216 281 356 440 557 356 440 557 305 377 477 589 713
in
3
/s -
-
11.6
15.0
11.6 15.0 18.8 11.6 15.0 18.8 24.5 31.1 11.6 15.0 18.8 24.5 31.1 18.8 24.5 31.1 13.2 17.1 21.7 26.8 34.0 13.2 17.1 21.7 26.8 34.0 21.7 26.8 34.0 18.6 23.0 29.1 35.9 43.5
Injection
Velocity
HIGH
mm/s - 500 500 500 500 500
350 350 350 300
in/s - 19.7 19.7 19.7 19.7 19.7 13.8 13.8 13.8 11.8
Plasticizing
capacity
PS
g/sec 2.2 3.3 6.1 7.8 6.1 7.8 9.7 6.1 6.9 11.1 16.9 23.1 6.1 6.9 11.1 16.9 23.1 11.1 16.9 23.1
11.1 16.9 23.1 30.6 33.3 11.1 16.9 23.1 30.6 33.3 23.1 30.6 33.3 18.9 27.2 33.3 44.4 52.8
oz/sec 0.08 0.12 0.22 0.27 0.2 0.3 0.3 0.2 0.2 0.4 0.6 0.8 0.2 0.2 0.4 0.6 0.8 0.4 0.6 0.8 0.4 0.6 0.8 1.1 1.2 0.4 0.6 0.8 1.1 1.2 0.8 1.1 1.2 0.7 1.0 1.2 1.6 1.9
Screw speed RPM 480 480 420 420 420 420 380 420 390 400 390 350 420 390 400 390 350 400 390 350 400 390 350 320 285 400 390 350 320 285 350 320 285 285 285 285 255 230
Nozzle touch force
kN 5.98 5.98 9.8 9.8 9.8 11.8 11.8 11.8 29.4 29.4
US Ton 0.66 0.66 1.1 1.1 1.1 1.3 1.3 1.3 3.3 3.3
GENERAL
Heater Capacity kW 3.4 4.8 4.7 5.4 4.7 5.8 6.8 4.7 5.8 6.8 6.8 6.8 11.2 6.8 11.2 11.2 11.2 13.6 15.2
Machine
Dimensions
L x W x H m 2.9 x 1.0 x 1.6 3.2 x 1.0 x 1.6 4.0 x 1.2 x 1.6 4.0 x 1.2 x 1.6 4.1 x 1.2 x 1.6 4.0 x 1.2 x 1.6 4.1 x 1.2 x 1.6 4.6 x 1.3 x 1.7
4.6 x 1.3 x 1.7 4.9 x 1.3 x 1.7 4.8 x 1.4 x 1.8 4.9 x 1.3 x 1.7 5.2 x 1.4 x 1.8 5.7 x 1.5 x 1.9 5.7 x 1.5 x 1.9 5.9 x 1.5 x 1.9 6.0 x 1.5 x 1.9
L x W x H ft 9.5 x 3.3 x 5.2 10.5 x 3.3 x 5.2 13.2 x 3.9 x 5.2 13.2 x 3.9 x 5.2 13.5 x 3.9 x 5.2 13.2 x 3.9 x 5.2 13.5 x 3.9 x 5.2 15.1 x 4.3 x 5.6 15.1 x 4.3 x 5.6 16.1 x 4.3 x 5.6 15.7 x 4.6 x 5.9 16.7 x 4.6 x 5.9 17.1 x 4.6 x 5.9 18.7 x 4.9 x 6.2 18.7 x 4.9 x 6.2 19.4 x 4.9 x 6.2 19.7 x 4.9 x 6.2
Machine weight
tf 2.0 2.0 3.0 3.2 3.3 4.2 4.2 4.3 5.2 5.3 7.0 7.0 7.3
US Ton 2.2 2.2 3.3 3.5 3.6 4.6 4.6 4.7 5.7 5.8 7.7 7.7 8.0
ITEM UNIT EC250SX EC310SX EC390SX EC5 00SX EC610SX
CLAMP
Clamp force
tf 230 280 350 450 550
US Ton 253.5 308.6 385.8 496 606.3
Tie bar
distance
H x V mm 610 x 560 730 x 660
810 x 730 870 x 810 960 x 900
H x V in 24.0 x 22.0 28.7 x 25.9 31.9 x 28.7 34.3 x 31.9 37.8 x 35.4
Platen
dimension
H x V mm 880 x 830 1030 x 960
1110 x 1030 1230 x 1160 1365 x 1300
H x V in 34.6 x 32.7 40.5 x 37.7 43.7 x 40.6 48.4 x 45.7 53.7 x 51.2
Clamp Stroke
mm 550 600 650 800 900
in 21.7 23.6 25.6 31.5 35.4
Maximum daylight
mm 1230 1350 1420 1600 1700
in 48.4 53.1 55.9 63.0 66.9
Mold
Height
Min. x Max mm 250 ~ 680 250 ~ 750
300 ~ 770 350 x 800 400 x 800
Min. x Max in 9.8 ~ 26.8 9.8 ~ 29.5 11.8 ~ 30.3 13.8 x 31.5 15.7 x 31.5
Ejector force
tf 5 6 6 13 13
US Ton 5.5 6.6 6.6 14.3 14.3
Ejector Stroke
mm 130 150 150 180 180
in 5.1 5.9 5.9 7.1 7.1
INJECTION
Injection Unit U48 i17 i8 i17 i8 i17 i26 i26 i36 i26 i36
Barrel code (4Y) (6Y) (8Y) (8A) (8B) Y AT B Y A B Y AT B Y A B Y AT B AT B AT B AT B AT B AT B
Screw Diameter
mm 36 40 45 50 55 50 60 70 45 50 55 50 60 70 45 50 55 50 60 70 70 80 70 80 80 90 70 80 80 90
in 1.42 1.57 1.77 1.97 2.17 1.97 2.36 2.76 1.77 1.97 2.17 1.97 2.36 2.76 1.77 1.97 2.17 1.97 2.36 2.76 2.76 3.15 2.76 3.15 3.15 3.54 2.76 3.15 3.15 3.54
Injection Capacity
cm
3
162 226 318 392 475 589 848 1155 318 392 475 589 848 1155 318 392 475 589 848 1155 1340 1750 1340 1750 1880 2380 1340 1750 1880 2380
in
3
9.9 13.8 19.4 23.9 29.0 35.9 51.7 70.5 19.4 23.9 29.0 35.9 51.7 70.5 19.4 23.9 29.0 35.9 51.7 70.5 81.8 106.8 81.8 106.8 114.7 145.2 81.8 106.8 114.7 145.2
Shot
Volume
PS
g 149 208 293 361 437 542 780 1062 293 361 437 542 780 1063
293 361 437 542 780 1063 1233 1610 1233 1610 1730 2190 1233 1610 1730 2190
oz 5.3 7.3 10.3 12.7 15.4 19.1 27.5 37.5 10.3 12.7 15.4 19.1 27.5 37.5 10.3 12.7 15.4 19.1 27.5 37.5 43.5 56.8 43.5 56.8 61.0 77.2 43.5 56.8 61.0 77. 2
PE
g 118 165 232 286 347 430 619 843 232 286 347 430 619 843 232 286 347 430 619 843 978 1278 978 1278 1372 1737 978 1278 1372 1737
oz 4.2 5.8 8.2 10.1 12.2 15.2 21.8 29.7 8.2 10.1 12.2 15.2 21.8 29.7 8.2 10.1 12.2 15.2 21.8 29.7 34.5 45.1 34.5 45.1 48.4 61.3 34.5 45.1 48.4 61.3
Maximum Injection
Pressure
MPa 247 253 247 200 165 288 200 147 247 200 165 288 200 147
247 200 165 288 200 147 190 145 190 145 190 150 190 145 190 150
PSI 35,800 36,700 35,800 29,000 23,900 41,800 29,000 21,300 35,800 29,000 23,900 41,800 29,000 21,300 35,800 29,000 23,900 41,800 29,000 21,300 27,600 21,000 27,600 21,000 27,600 21,800 27,600 21,000 27,600 21,800
Maximum Holding
Pressure
MPa 247 253 247 200 165 288 200 147 247 200 165 288 200 147
247 200 165 288 200 147 160 122 160 122 160 126 160 122 160 126
PSI 35,800 36,700 35,800 29,000 23,900 41,800 29,000 21,300 35,800 29,000 23,900 41,800 29,000 21,300 35,800 29,000 23,900 41,800 29,000 21,300 23,200 17,700
23,200 17,70 0
23,200 18,300 23,200 17,700 23,200 18,300
Injection Rate STD
cm
3
/s 163 201 254 314 380 314 452 616 254 314 380 314 452 616 254 314 380 314 452 616 616 804
616 804
704 891 616 804 704 891
in
3
/s 9.9 12.3 15.5 19.2 23.2 19.2 27.6 37.6 15.5 19.2 23.2 19.2 27.6 37.6 15.5 19.2 23.2 19.2 27.6 37.6 37.6 49.1
37.6 49.1
43.0 54.4 37.6 49.1 43.0 54.4
Injection
Velocity
STD
mm/s 160 160 160 160
160 160 160
160
140 160 140
in/s 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 5.5 6.3 5.5
Injection Rate HIGH
cm
3
/s 305 377 477 589 713 589 848 1155 477 589 713 589 848 1155 477 589 713 589 848 1155 – – – – – – – – – –
in
3
/s 18.6 23.0 29.1 35.9 43.5 35.9 51.7 70.5 29.1 35.9 43.5 35.9 51.7 70.5 29.1 35.9 43.5 35.9 51.7 70.5 – – – – – – – – – –
Injection
Velocity
HIGH
mm/s 300 300 300 300
300 300 – – – – – – – – – –
in/s 11.8 11.8 11.8 11.8 11.8 11.8 – – – – – – – – – –
Plasticizing
capacity (PS)
STD
g/sec 18.9 27.2 33.3 44.4 52.8 35.8 64.4 75.8 33.3 44.4 52.8 44.4 64.4 75.8
33.3 44.4 52.8 35.8 64.4 75.8 72.2
94.4
72.2 94.4 94.4 111.1 72.2 94.4 94.4 111.1
oz/sec 0.7 1.0 1.2 1.6 1.9 1.3 2.3 2.7 1.2 1.6 1.9 1.6 2.3 2.7 1.2 1.6 1.9 1.3 2.3 2.7 2.5
3.3
2.5 3.3 3.3 3.9 2.5 3.3 3.3 3.9
HIGH
TORQUE
g/sec – – – – – – – – – – – – – –
– – – – – – 47.2
63.9
47.2 63.9 61.1 77.8 47. 2 63.9 61.1 77.8
oz/sec – – – – – – – – – – – – – – – – – – – – 1.7
2.3
1.7 2.3 2.2 2.7 1.7 2.3 2.2 2.7
Screw
torque
STD
Nm – – – – – – – – – – – – – –
– – – – – – 2580 2580 2580 2580 3310 3310 2580 2580 3310 3310
ft-lbf – – – – – – – – – – – – – – – – – – – – 1903 1903 1903 1903 2441 2441 1903 1903 2441 2441
HIGH
TORQUE
Nm – – – – – – – – – – – – – –
– – – – – – 3310 3310 3310 3310 4610 4610 3310 3310 4610 4610
ft-lbf – – – – – – – – – – – – – – – – – – – – 2441 2441 2441 2441 3400 3400 2441 2441 3400 3400
Screw
speed
STD RPM 285 285 285 255 230 255 220 180 285 255 230 255 220 180
285 255 230 255 220 180 180 170 180 170 170 150 180 170 170 150
HIGH
TORQUE
RPM – – – – – – – – – – – – – –
– – – – – – 120 120 120 120 115 115 120 120 115 115
Nozzle touch force
kN 29.4 29.4 29.4 29.4 29.4 29.4 4.5 4.5 6 4.5 6
US Ton 3.3 3.3 3.3 3.3 3.3 3.3 5.0 5.0 6.6 5.0 6.6
GENERAL
Heater Capacity kW 11.2 13.6 15.2 21.6 15.2 15.2 21.6 21.6 22.3 22.3 29.5 22.3 29.5
Machine
Dim.
L x W x H m 6.0 x 1.6 x 2.0 6.2 x 1.6 x 2.0 6.3 x 1.6 x 2.0 6.8 x 1.8 x 2.2 6.7 x 2.0 x 2.1 7.0 x 2.0 x 2.1
7.0 x 2.1 x 2.2 7.3 x 2.1 x 2.2 7.9 x 2.1 x 2.2 8.0 x 2.2 x 2.3 8.4 x 2.3 x 2.3 8.5 x 2.3 x 2.3 8.3 x 2.3 x 2.3 8.7 x 2.4 x 2.3 8.8 x 2.4 x 2.3
L x W x H ft 19.6 x 5.2 x 6.6 20.3 x 5.2 x 6.6 20.7 x 5.2 x 6.6 21.7 x 5.6 x 7.2 22.0 x 6.6 x 6.9 23.0 x 6.6 x 6.9 23.0 x 6.9 x 7.2 24.0 x 6.9 x 7.2 25.9 x 6.9 x 7.5 26.2 x 7.2 x 7.5 27.6 x 7.5 x 7.5 27.9 x 7.5 x 7.5 27.2 x 7.5 x 7.5 28.5 x 7.9 x 7.5 28.9 x 7.9 x 7.5
Machine weight
tf 9.2 9.3 12.4 13.5 14.7 17.2 17. 2 18.7 25.5 26.7 30.2 31.4
US Ton 10.1 10.3 13.6 14.9 16.2 19.0 19.0 20.6 28.1 29.4 33.3 34.6
SPECIFICATIONS
ITEM UNIT EC250SX EC310SX EC390SX EC5 00SX EC610SX
CLAMP
Clamp force
tf 230 280 350 450 550
US Ton 253.5 308.6 385.8 496 606.3
Tie bar
distance
H x V mm 610 x 560 730 x 660
810 x 730 870 x 810 960 x 900
H x V in 24.0 x 22.0 28.7 x 25.9 31.9 x 28.7 34.3 x 31.9 37.8 x 35.4
Platen
dimension
H x V mm 880 x 830 1030 x 960
1110 x 1030 1230 x 1160 1365 x 1300
H x V in 34.6 x 32.7 40.5 x 37.7 43.7 x 40.6 48.4 x 45.7 53.7 x 51.2
Clamp Stroke
mm 550 600 650 800 900
in 21.7 23.6 25.6 31.5 35.4
Maximum daylight
mm 1230 1350 1420 1600 1700
in 48.4 53.1 55.9 63.0 66.9
Mold
Height
Min. x Max mm 250 ~ 680 250 ~ 750
300 ~ 770 350 x 800 400 x 800
Min. x Max in 9.8 ~ 26.8 9.8 ~ 29.5 11.8 ~ 30.3 13.8 x 31.5 15.7 x 31.5
Ejector force
tf 5 6 6 13 13
US Ton 5.5 6.6 6.6 14.3 14.3
Ejector Stroke
mm 130 150 150 180 180
in 5.1 5.9 5.9 7.1 7.1
INJECTION
Injection Unit U48 i17 i8 i17 i8 i17 i26 i26 i36 i26 i36
Barrel code (4Y) (6Y) (8Y) (8A) (8B) Y AT B Y A B Y AT B Y A B Y AT B AT B AT B AT B AT B AT B
Screw Diameter
mm 36 40 45 50 55 50 60 70 45 50 55 50 60 70 45 50 55 50 60 70 70 80 70 80 80 90 70 80 80 90
in 1.42 1.57 1.77 1.97 2.17 1.97 2.36 2.76 1.77 1.97 2.17 1.97 2.36 2.76 1.77 1.97 2.17 1.97 2.36 2.76 2.76 3.15 2.76 3.15 3.15 3.54 2.76 3.15 3.15 3.54
Injection Capacity
cm
3
162 226 318 392 475 589 848 1155 318 392 475 589 848 1155 318 392 475 589 848 1155 1340 1750 1340 1750 1880 2380 1340 1750 1880 2380
in
3
9.9 13.8 19.4 23.9 29.0 35.9 51.7 70.5 19.4 23.9 29.0 35.9 51.7 70.5 19.4 23.9 29.0 35.9 51.7 70.5 81.8 106.8 81.8 106.8 114.7 145.2 81.8 106.8 114.7 145.2
Shot
Volume
PS
g 149 208 293 361 437 542 780 1062 293 361 437 542 780 1063
293 361 437 542 780 1063 1233 1610 1233 1610 1730 2190 1233 1610 1730 2190
oz 5.3 7.3 10.3 12.7 15.4 19.1 27.5 37.5 10.3 12.7 15.4 19.1 27.5 37.5 10.3 12.7 15.4 19.1 27.5 37.5 43.5 56.8 43.5 56.8 61.0 77.2 43.5 56.8 61.0 77. 2
PE
g 118 165 232 286 347 430 619 843 232 286 347 430 619 843 232 286 347 430 619 843 978 1278 978 1278 1372 1737 978 1278 1372 1737
oz 4.2 5.8 8.2 10.1 12.2 15.2 21.8 29.7 8.2 10.1 12.2 15.2 21.8 29.7 8.2 10.1 12.2 15.2 21.8 29.7 34.5 45.1 34.5 45.1 48.4 61.3 34.5 45.1 48.4 61.3
Maximum Injection
Pressure
MPa 247 253 247 200 165 288 200 147 247 200 165 288 200 147
247 200 165 288 200 147 190 145 190 145 190 150 190 145 190 150
PSI 35,800 36,700 35,800 29,000 23,900 41,800 29,000 21,300 35,800 29,000 23,900 41,800 29,000 21,300 35,800 29,000 23,900 41,800 29,000 21,300 27,600 21,000 27,600 21,000 27,600 21,800 27,600 21,000 27,600 21,800
Maximum Holding
Pressure
MPa 247 253 247 200 165 288 200 147 247 200 165 288 200 147
247 200 165 288 200 147 160 122 160 122 160 126 160 122 160 126
PSI 35,800 36,700 35,800 29,000 23,900 41,800 29,000 21,300 35,800 29,000 23,900 41,800 29,000 21,300 35,800 29,000 23,900 41,800 29,000 21,300 23,200 17,700
23,200 17,70 0
23,200 18,300 23,200 17,700 23,200 18,300
Injection Rate STD
cm
3
/s 163 201 254 314 380 314 452 616 254 314 380 314 452 616 254 314 380 314 452 616 616 804
616 804
704 891 616 804 704 891
in
3
/s 9.9 12.3 15.5 19.2 23.2 19.2 27.6 37.6 15.5 19.2 23.2 19.2 27.6 37.6 15.5 19.2 23.2 19.2 27.6 37.6 37.6 49.1
37.6 49.1
43.0 54.4 37.6 49.1 43.0 54.4
Injection
Velocity
STD
mm/s 160 160 160 160
160 160 160
160
140 160 140
in/s 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 5.5 6.3 5.5
Injection Rate HIGH
cm
3
/s 305 377 477 589 713 589 848 1155 477 589 713 589 848 1155 477 589 713 589 848 1155 – – – – – – – – – –
in
3
/s 18.6 23.0 29.1 35.9 43.5 35.9 51.7 70.5 29.1 35.9 43.5 35.9 51.7 70.5 29.1 35.9 43.5 35.9 51.7 70.5 – – – – – – – – – –
Injection
Velocity
HIGH
mm/s 300 300 300 300
300 300 – – – – – – – – – –
in/s 11.8 11.8 11.8 11.8 11.8 11.8 – – – – – – – – – –
Plasticizing
capacity (PS)
STD
g/sec 18.9 27.2 33.3 44.4 52.8 35.8 64.4 75.8 33.3 44.4 52.8 44.4 64.4 75.8
33.3 44.4 52.8 35.8 64.4 75.8 72.2
94.4
72.2 94.4 94.4 111.1 72.2 94.4 94.4 111.1
oz/sec 0.7 1.0 1.2 1.6 1.9 1.3 2.3 2.7 1.2 1.6 1.9 1.6 2.3 2.7 1.2 1.6 1.9 1.3 2.3 2.7 2.5
3.3
2.5 3.3 3.3 3.9 2.5 3.3 3.3 3.9
HIGH
TORQUE
g/sec – – – – – – – – – – – – – –
– – – – – – 47.2
63.9
47.2 63.9 61.1 77.8 47. 2 63.9 61.1 77.8
oz/sec – – – – – – – – – – – – – – – – – – – – 1.7
2.3
1.7 2.3 2.2 2.7 1.7 2.3 2.2 2.7
Screw
torque
STD
Nm – – – – – – – – – – – – – –
– – – – – – 2580 2580 2580 2580 3310 3310 2580 2580 3310 3310
ft-lbf – – – – – – – – – – – – – – – – – – – – 1903 1903 1903 1903 2441 2441 1903 1903 2441 2441
HIGH
TORQUE
Nm – – – – – – – – – – – – – –
– – – – – – 3310 3310 3310 3310 4610 4610 3310 3310 4610 4610
ft-lbf – – – – – – – – – – – – – – – – – – – – 2441 2441 2441 2441 3400 3400 2441 2441 3400 3400
Screw
speed
STD RPM 285 285 285 255 230 255 220 180 285 255 230 255 220 180
285 255 230 255 220 180 180 170 180 170 170 150 180 170 170 150
HIGH
TORQUE
RPM – – – – – – – – – – – – – –
– – – – – – 120 120 120 120 115 115 120 120 115 115
Nozzle touch force
kN 29.4 29.4 29.4 29.4 29.4 29.4 4.5 4.5 6 4.5 6
US Ton 3.3 3.3 3.3 3.3 3.3 3.3 5.0 5.0 6.6 5.0 6.6
GENERAL
Heater Capacity kW 11.2 13.6 15.2 21.6 15.2 15.2 21.6 21.6 22.3 22.3 29.5 22.3 29.5
Machine
Dim.
L x W x H m 6.0 x 1.6 x 2.0 6.2 x 1.6 x 2.0 6.3 x 1.6 x 2.0 6.8 x 1.8 x 2.2 6.7 x 2.0 x 2.1 7.0 x 2.0 x 2.1
7.0 x 2.1 x 2.2 7.3 x 2.1 x 2.2 7.9 x 2.1 x 2.2 8.0 x 2.2 x 2.3 8.4 x 2.3 x 2.3 8.5 x 2.3 x 2.3 8.3 x 2.3 x 2.3 8.7 x 2.4 x 2.3 8.8 x 2.4 x 2.3
L x W x H ft 19.6 x 5.2 x 6.6 20.3 x 5.2 x 6.6 20.7 x 5.2 x 6.6 21.7 x 5.6 x 7.2 22.0 x 6.6 x 6.9 23.0 x 6.6 x 6.9 23.0 x 6.9 x 7.2 24.0 x 6.9 x 7.2 25.9 x 6.9 x 7.5 26.2 x 7.2 x 7.5 27.6 x 7.5 x 7.5 27.9 x 7.5 x 7.5 27.2 x 7.5 x 7.5 28.5 x 7.9 x 7.5 28.9 x 7.9 x 7.5
Machine weight
tf 9.2 9.3 12.4 13.5 14.7 17.2 17. 2 18.7 25.5 26.7 30.2 31.4
US Ton 10.1 10.3 13.6 14.9 16.2 19.0 19.0 20.6 28.1 29.4 33.3 34.6
ITEM UNIT EC720SX EC950SX EC1100SX EC1450S X
CLAMP
Clamp force
tf 650 850 1000 1300
U S T o n 716.5 937 1102 1433
Tie bar
distance
H x V mm 1060 x 960 1320 x 1320
1300 x 1300
1400 x 1400
H x V in 41.7 x 37.7 51.9 x 51.9 51.2 x 51.2 55.1 x 55.1
Platen
dimension
H x V mm 1500 x 1400 1790 x 1790 1790 x 1790 2000 x 2000
H x V in 59.0 x 55.1 70.4 x 70.4 70.5 x 70.5 78.7 x 78.7
Clamp Stroke
mm 1000 1200 1200 1500
in 39.4 47.2 47.2 59
Maximum daylight
mm 2050 2300 2300 2800
in 80.7 90.6 90.6 110.2
Mold
Height
Min. x Ma x mm 450 x 1050 500 x 1100 500 x 1100 650 x 1300
M i n . x M a x in 17.7 x 41.3 19.6 x 43.3 19.7 x 43.3 25.6 x 51.2
Ejector force
tf 18 18 18 28.5
U S T o n 19.8 19.8 19.8 31.4
Ejector Stroke
mm 200 200
200
250
in 7.9 7.9 7.9 9.8
INJECTION
Injection Unit i61 i78 i61 i78 i61 i78
i78
i120
i155
Barrel code AT B AT B AT B AT B AT
B AT B AT B
AT B
AT B
Screw Diameter
mm 95 105 105 120 95 105 105 120 95
105 105 120 105 120
115 125
125 140
in 3.74 4.13 4.13 4.72 3.74 4.13 4.13 4.72 3.74 4.13 4.13 4.72 4.13 4.72 4.53 4.92 4.92 5.51
Injection Capacity
cm
3
3150 3850 4320 5650 3150 3850 4320 5650 3150 3850
4320
5650 4320 5650 6560 7750 8430 10570
in
3
192.2 234.9 263.6 344.8 192.2 234.9 263.6 344.8 192.2 234.9
263.6
344.8 263.6 344.8 400.3 472.9 514.4 645.0
Shot
Volume
PS
g 2898 3542 3974 5198 2898 3542 3974 5198 2900 3540 3980 5200 3980 5200 6040 7130 7750 9730
oz 102.2 124.9 140.2 183.3 102.2 124.9 140.2 183.3 102.3
124.9 140.4 183.4
140.4 183.4 213.1 251.5 273.4 343.2
PE
g 2300 2811 3154 4125 2300 2811 3154 4125 2300
2810 3160 4120
3160 4120 4790 5660 6150 7720
oz 81.1 99.2 111.3 145.5 81.1 99.2 111.3 145.5 81.1 99.1 111.5 145.3 111.5 145.3 167.0 199.6 216.9 272.3
Maximum Injection
Pressure
MPa 180 147 180 138 180 147 180 138 180
147 180 138
180 138 180 152 180 143
PSI 26,100
21,300
26,100 20,000 26,100
21,300
26,100 20,000 26100 21300 26100 20000 26100 20000 26100 22000 26100 20700
Maximum Holding
Pressure
MPa 150 123 150 115 150 123 150 115 150
123 150 115
150 115 150 127 150 119
PSI
21,800
17,800 21,800 16,700
21,800
17,800 21,800 16,700 21800
17800 21800 16700
21800 16700 21800 18400 21800 17300
Injection
Rate
STD
cm
3
/s 1063 1299 1299 1696 1063 1299 1299 1696 1060
1290 1290 1690
1290 1690 1450 1710 1470 1840
in
3
/s 64.9 79.3 79.3 103.5 64.9 79.3 79.3 103.5 64.7 78.7
78.7 103.1
78.7 103.1 88.5
104.3 89.7 112.3
Injection
Velocity
STD
mm/s 150 150 150 150 150 150 150 140 120
in/s 5.9 5.9 5.9 5.9 5.9 5.9 5.9 5.5 4.7
Plasticizing
capacity
(PS)
STD
g/sec 116.7 136.1 136.1 161.1 116.7 136.1 136.1 161.1
116.7 136.1 136.1 161.1 136.1 161.1 144.4 161.1 163.9 191.7
oz/sec 4.1 4.8 4.8 5.7 4.1 4.8 4.8 5.7
4.1 4.8 4.8 5.7 4.8 5.7 5.1 5.7 5.8 6.8
HIGH
TORQUE
g/sec 80.6 102.8 75 102.8 80.6 102.8 75 102.8
80.6 102.8 75 102.8 75.0 102.8 102.8 122.2 116.7 152.8
oz/sec 2.8 3.6 2.6 3.6 2.8 3.6 2.6 3.6
2.8 3.6 2.6 3.6 2.6 3.6 3.6 4.3 4.1 5.4
Screw
torque
STD
Nm 5500 5500 7090 7090 5500 5500 7090 7090
5500 5500 7090 7090 7090 7090 9150 9150 14500 14500
ft-lbf 4057 4057 5229 5229 4057 4057 5229 5229
4057 4057 5229 5229 5229 5229 6749
6749
10695 10695
HIGH
TORQUE
Nm 7090 7090 10300 10300 7090 7090 10300 10300
7090 7090 10300 10300 10300 10300 13700
13700
17300 17300
ft-lbf 5229 5229 7597 7597 5229 5229 7597 7597
5229 5229 7597 7597 7597 7597
10105 10105
12760 12760
Screw
speed
STD RPM 140 127 127 110 140 127 127 110
140 127 127 110 127 110
110 101
101 90
HIGH
TORQUE
RPM 95 95 71 71 95 95 71 71
95 95 71 71 71
78 78
72
Nozzle touch force
kN 6 6
6 64.72
101
101
U S Ton 6.6 6.6
6.6 6.6
10.3
10.3
GENERAL
Heater Capacity kW 44.0 57.2 44.0 57.2 44.4 57. 2 57.2 69.4 84.1
Machine
Dim.
L x W x H m
9.8 x 2.6 x 2.7 10.1 x 2.6 x 2.7 10.4 x 2.6 x 2.7 10.6 x 2.9 x 2.7 10.6 x 2.9 x 2.7 10.9 x 2.9 x 2.7 10.6 x 2.9 x 2.7 10.9 x 2.9 x 2.7 10.9 x 2.9 x 2.7 12.8 x 3.2 x 3.2 12.8 x 3.2 x 3.2 13.5 x 3.5 x 3.2
L x W x H ft
32.1 x 8.6 x 8.9 33.2 x 8.6 x 8.9 34.1 x 8.6 x 8.9 34.8 x 9.5 x 8.9 34.8 x 9.5 x 8.9 35.8 x 9.5 x 8.9 34.8 x 9.5 x 8.9 35.8 x 9.5 x 8.9 35.8 x 9.5 x 8.9 42.0 x 10.5 x 10.5 42.0 x 10.5 x 10.5 44.3 x 11.5 x 10.5
Machine weight
tf 40.0 41.5 53.5 55.0 55 57
82
89
99
U S Ton 44.1 45.7 59.0 60.6 60.6 62.8 90.4 98.1 109.1
SPECIFICATIONS
Injection/Plasticization
u
Open nozzle
u
Barrel - anti-corrosion/wear
u
Standard screw assembly, high
kneading DBG design
u
Hopper inlet rust-preventive sleeve
u
Barrel heater
u
Friction-Free Drive
u
Digital load cell
u
Purge shield
u
Double heater cover
u
DST-Fill
u
Pressure linear correction
u
Programmed purge circuit
u
VHI control
u
FIT Control
u
Laminar control
u
EC-SX 12-Speed/8-pressure injection
programmed control
u
Shift to hold mode selection
u
Shift to hold correction control
u
Injection speed FF control
u
Screw speed/back pressure
programmed control
u
Automatic screw back pressure
reduction control
u
Automatic charging deceleration
control
u
Decompress before/after charge
u
Charge delay timer
u
Screw cold start prevention device
u
Heater SSR control
u
Heater band failure indicating circuit
u
Hopper Throat temperature controller
u
Barrel temperature FF control
u
Programmed heat-Up circuit
u
Simultaneous barrel heat-up control
u
Barrel Temperature shift circuit
u
Retention resin overheat prevention
circuit
u
Manual back pressure setting
Clamp unit/ejector and
functions
u
Link line toggle unit
u
Double rigid body platen
u
Mold platen
u
Locating hold
u
Movable platen supporting device
u
Mechanical safety device
u
Interface for dual hydraulic core pulls
standard
u
Holes tapped for installation of take-
out robot
u
Ejection servo motor with brake
u
Mold open while charging
(simultaneous motion)
u
Automatic lubricator
u
Dynamic acceleration/deceleration
control
u
DST-Press control
u
3-step high-speed programmed
control
u
Plestrol control (coining for clamp)
u
Clamp pressure digital display in two
steps
u
Sensitive mold protection control -
provides torque monitor and limiter
in two high-speed ranges, and
torque/time limiter in low-pressure
clamp range
u
Automatic mold thickness adjust
circuit
u
Low pressure and slow speed circuit
for mold set-up mode
u
Lock-up delay timer
u
Lock-up speed digital setting
u
Setting of number of repeated
ejections
u
3-step ejection speed programmed
control
u
Repeated ejection
control
u
RA ejection control
STANDARD FEATURES
EC-SX SERIES - AC SERVO ELECTRIC INJECTION MOLDING MACHINES
Clamp unit/ejector and functions
continued
u
Ejector retraction check circuit
u
Ejector plate, ejecting rod
u
Gate cut circuit
u
Ejection force digital setting
u
Ejection hold time setting
u
Ejection during mold opening
u
Ejection torque monitor
u
Mold open halt - Enables mold
opening at an arbitrary position
Controller (EC-SX Series)
u
Six programmable outputs standard
u
Step switch/ten key input
u
Setting data memory for 300 sets of
molds
u
External interface SPI
u
Digital display
u
Graphic display
u
Profile display/storing/measure
functions
u
Quality monitoring
u
Diagnostic function
u
Operation select function at
production completion
u
MOLDLYZER
u
iPAQET LITE
u
LCD touch panel
u
High-Speed control cycle
u
List setting screen
u
Operation indicator
u
External output signal customize
function
u
Password function
TOSHIBA MACHINE
PANTONE 193
TOSHIBA MACHINE
CMYK
TOSHIBA MACHINE
K
TOSHIBA MACHINE
WHITE
EC-SX Dimensions
MODEL INJ. UNIT
SCREW DIA L L1 L2 D D1 H H1 H2
mm Inch
EC30SX
i 0.4 16 /18 113.9
49.6
24.6
39.3 20.7 55.8 41.6 62.6
i 1
22/25 122.8 29.7
20 121.3 28.1
EC55SX
EC85SX
U21
22/25 155.1
68.9
35.0
46.9 23.8 62.4 46.1 62.0
28 158.3 37. 4
U22
22 155.1 35.0
25 158.3 37. 4
28/32 161.5 40.7
36 164.7 43.8
EC110SX
U32
28/32 180.8
82.3
41.9
49.8 25.2 64.8 46.7 64.6
36 184.0 45.0
U34
28/32 180.8 41.9
36/40 191.1 49.2
45 195.2 53.3
EC140SX U34
28/32 18 7.7
89.2
41.9
54.7 2 7.4 6 7.7 48.5 66.5 36/40 198.6 49.8
36 202.7 53.9
EC200SX
U44
36/40 223.3
102.3
51.7
60.2 30.6 71.0 49.3 70.5
45 2 27. 4 55.8
U48
36 223.3 51.7
40 230.7 56.2
45/50 234.6 60.1
55 238.7 64.2
EC250SX U48
36 2 37. 0
114.2
53.5
63.9 32.4 76.6 52.0 73.3
40 244.3 58.0
45/50 248.2 61.9
55 252.3 66.0
EC390SX U5 50/60/70 284.3 132.8 85.3 82.1 44.2 8 4.1 53.6 84.6
Note: This is the real height without mounting pads.
All dimensions subject to change without notice.
MODEL INJ. UNIT
SCREW DIA L L1 L2 L3 D D1 H H1 H2
mm Inch
EC500SX
i26
70
313.6
145.9
83.7
7.6
81.9 41.7 86.6 55.1
86.2
80 91.5
i36
80
324.8
91.7 6.9
87.8
90 99.6 6.9
EC610SX
i26
70
326.6
157.3
85.2
7.6
87.8 45.9 86.6 55.1
86.2
80 93.1
i36
80
337.8
93.3 14.8
87.8
90 101.2 6.9
EC720SX
i61
95
380.9 181.1
111.5 6.8
97.6 50.4 86.6 55.1
99.4
105 119.4 14.6
i78
105 127.2
22.5 101.4
120 139.1
EC950SX
i61
95
414.8 204.7
104.7 0
112.2 60.4 94.5 59.1
103.4
105 112.6 6.6
i78
105 120.4 14.4
105.4
120 132.2 26.3
EC1100SX
i61
95
414.8 204.7
104.7 0
112.2 60.4 94.5 59.1
103.4
105 112.6 6.6
i78
105 120.4 14.4
105.4
120 132.2 26.3
EC1450SX
i-120 A 115 495.9 247.91 142.4 4.6 123.5 62.28 121.2 65.7 109.8
i120 B 125 503.8 150.3 -3.6
EC-SX Dimensions
NOTES
Note: This is the real height without mounting pads.
All dimensions subject to change without notice.
Toshiba Machine Co., America
Chicago Head Office
755 Greenleaf Avenue
Elk Grove Village, IL 60007
Ph: 847-593-1616
Email: [email protected]
Sales, Service, Technical Center and
Technical Support
Reach for the impossible.
Achieve the incredible.
Your investment in Toshiba Machine molding machines and equipment brings with it our
comprehensive committment to service and support. It gives you access to assistance and technical
help in locations across the country, plus on-site assistance when you need a hands-on solution.
We appreciate the opportunity to become part of your company and look forward to providing
solutions that help you “achieve the incredible.”
Toshiba Machine Co., America – Los Angeles Office
1440 South Balboa Avenue
Ontario, CA 91761
Ph: 909-923-4009
Email: [email protected]
Sales, Service, Technical Center and Technical Support
Toshiba Machine Co., America – New Jersey Office
1578 Sussex Turnpike South
Randolph, NJ 07869
Ph: 973-252-9956
Email: [email protected]
Sales, Service, Technical Center and Technical Support
Toshiba Machine Co., Ltd.
2-2, Uchisaiwaicho 2-Chome, Chiyoda-ku, Tokyo 100-8503, Japan
Ph: +81-3-3509-0319; Fax: +81-3-3509-0331
Toshiba Machine Co., Canada Ltd – Canada Office
6 Shields Court, Suite 101
Markham, ON L3R 4S1
Canada
Ph: 905-479-9111
Email: [email protected]
Sales, Service, Technical Center and Technical Support
Toshiba Machine Co., America – Mexico Office
Av. Mineral de Valenciana #202, Col. Santa Fe C.P. 36275
Puerto Interior, Silao, Guanajuato
Mexico
Ph: (52) 472-748-5400
Email: [email protected]
Sales, Service, Technical Center and Technical Support