INSTRUCTIONS ANIMAL CLIPPERS AND TRIMMERS

INSTRUCTIONS

ANIMAL CLIPPERS AND TRIMMERS

TABLE OF CONTENTS

These clippers and trimmers are designed for use in commercial dog grooming environments.

Save these instructions for future reference.

Please read all instructions carefully to familiarise yourself

with the product before using.

For any further assistance or information call Customer Services on

T: 01227 740066

or visit

W: www.wahl.co.uk

E: customer[email protected]

IMPORTANT SAFEGUARDS 3

USEFUL INFORMATION ABOUT YOUR PRODUCT 5

BLADES 5

PRODUCT INSTRUCTIONS

MAINS CLIPPERS

MAX 45 - KM6245 / WM6245

MAINS POWERED CORDED CLIPPER 6

KM5 / KM10 - WM6260 / WM6261

MAINS POWERED DOG CLIPPER 10

POWER GRIP - 8879

MAINS POWERED DOG CLIPPER 14

ARCO - WM6854

RECHARGEABLE DOG CLIPPER 18

BRAVURA - WM6870

CORD/CORDLESS DOG CLIPPER 22

TRIMMERS

BRAVMINI - WM6590

RECHARGEABLE DOG TRIMMER 27

MINI ARCO - WM6565

CORD/CORDLESS DOG TRIMMER 30

STAINLESS STEEL BLADES AND COMBS 32

BATTERY REPLACEMENT, REMOVAL & DISPOSAL 33

WIRING & DISPOSAL

IMPORTANT SAFEGUARDS

When using your electrical appliance, basic safety precautions should always be followed,

including the following:

REQUIREMENTS

► Readtheinstructionmanualinfulltofamiliariseyourselfwith

  theproductbeforetherstuse.

► Thisappliancecanbeusedbychildrenfromaged14years

and above and persons with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, if

they have been given supervision or instruction concerning

use of the appliance in a safe way and understand the

hazards involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children

without supervision.

► Usethisapplianceonlyforitsintendedpurpose.

HAZARDS

Danger! Electric shock due to damage to appliance

► Donotoperatetheappliancewithabrokencord,plugor

charger, or if the appliance malfunctions, or is dropped or

damaged in anyway.

► Anyservicingorrepairsmustbeperformedbyanauthorised

service representative.

► Theuseofattachmentsthatarenotsuppliedbythe

manufacturermaycausere,electricshockorinjuryand

damage to the appliance.

Danger! Electric shock due to penetration of liquid

► Toprotectagainstriskofelectricalshock,neverimmersethe

unit or let it come into contact with water or any other liquids.

Do not use the unit with wet hands. If the appliance should

become wet, damp or fall in water, remove plug from mains

socket immediately. Do not put your hands in the water. Do not

take into bathroom.

Danger of explosion

► Never use the appliance where aerosol (spray) products are

being used or where oxygen is.

► Donotexposetheappliancetotemperaturesbelow0˚C

  andabove+40˚Cforanylengthoftime.Avoiddirectexposure

to sunlight.

Warning! Injuries due to incorrect handling

► Cuttingbladesmaybecomehotafterprolongeduse.

► Switchotheapplianceandunplugfromoutletwhennotin

  use,beforeputtingonortakingoattachmentsandalso

before cleaning the appliance.

► Neveruseyourappliancewithoutpayingattention!Except

when charging always unplug this appliance from the

electricity outlet immediately after using.

► Theseappliancesareintendedforanimalhairtrimmingand

clipping only.

Caution! Danger of product damage

► Donotwrapthecordaroundtheappliance.

► Donotuseoutdoorsorindampareas.

► Nevercarrytheunitbyitspowercord.

► Donotdroporinsertanyobjectintoanyopening.

Covers all models:

Emission sound pressure level: max. <70 dB(A)

Vibration: < 2,5 m/s2

USEFUL INFORMATION ABOUT YOUR PRODUCT

Essential information

For maximum eciency, durability and satisfaction from Wahl clippers and trimmers,

please note the following points:-

• Regularly apply a few drops of oil to the blades during clipping/trimming. Clipper

oil lubricates the blades and will ensure your clippers or trimmers perform to

their maximum capacity. Without oil, friction is increased therefore generating

heat.Ifbladesaregettinghottheninsucientoilisbeingappliedortheblades

need cleaning or sharpening.

• Always ensure the animal coat is dry, as clean as possible and brushed to

remove tangles, grease and dirt particles from the hair.

• During operation, take time to regularly brush hairs and dirt from the blades.

• We recommend use of Wahl Hygienic Spray to ensure grease and dirt particles

areushedfromthebladesurface.DO NOT use water to clean the blades.

• Always oil the blades after cleaning.

• Alwayscleanyourmachineandbladesthoroughlywhenyouhavenished

clipping. Do not separate the top and bottom blade when cleaning.

• Ifyourproducthasanairlterensureitisclearofobstructionstoavoid

overheating the motor.

• Whenever storing your appliance, disconnect all cables and store your clipping/

trimming kit in a dry, temperate environment.

• Always oil your blades before use and before storage to prevent atmospheric

moisture causing damage to the blade surface.

BLADES

The blades are the single most important part of a clipper or trimmer and must be

well maintained at all times for maximum cutting performance.

Cutting hair does not blunt the blades. Abrasive particles on the animal’s hair, such

as dirt, sand, grease, etc will blunt the blades.

Bladeswillnotcutifabrasiveparticlesarepickedupandcarriedbytheoillm

between the blades. These particles tend to separate the blades from each other

and pull the hair as opposed to cutting it cleanly. Keeping your blades well oiled

performs the following important functions:-

• Providesalowfriction,verythinlmlubricantbetweenthecuttingbladessothe

blades can take a full cutting stroke without becoming hot from frictional heat.

• Flushes abrasive particles and hairs out from between the blades.

If you cut into dirt, immediately clean your blades with Wahl Hygienic Spray or Wahl

ClipperOiltoushoutthedirt.ALWAYS apply clipper oil after cleaning with hygienic

spray or coolant.

MAX 45 - CORDED DOG CLIPPER

432

Model: MAX 45 - KM6245 / WM6245

65 7

109

Model: MAX 45 CORDED DOG CLIPPER - KM6245 / WM6245

Description of parts (Fig. 1)

A. Blade set

B. Release button for blade set

C. On/oswitch

D. Airlter

E. Hang-up loop

F. Mains cable

G. Oil for blade set

H. Cleaning brush

Mains Operation

1. Connect to the mains power supply (Fig. 2)

2. Switchontheapplianceusingtheon/oswitchandswitchoafteruse(Fig.3).

The appliance has two speed settings.

Thesecanbeselectedviatheon/oswitch.

Setting I = slow speed

Setting II = high speed

Cutting with the attachment comb

The appliance can also be operated with attachment combs. Attachment combs can be used to extend

the cutting length range.

For best results we recommend using a #30 or #10 blade with the comb attachments.

Accessories are available from your local dealer.

Attaching / removing the attachment comb

1. Fit the attachment comb onto the bottom edge of the blade set (Fig. 4a) and push it over the cutting

edge of the bottom blade until it locks (Fig. 4b).

2. Push the attachment comb towards the cutting edge of the bottom blade (Fig. 5) and remove it from

the blade set.

Changing the blade set

To remove a blade set:

1. Switchotheapplianceusingtheon/oswitch(Fig.3).

2. Press the release button (B) (Fig. 6a) towards the blade set and lift the blade set away from the

housing (Fig. 6b).

3. Remove the blade set from the clip (Fig. 6c).

To attach a new blade set:

1. Attach the new blade set onto the clip (Fig. 8a).

2. Ensurethattheclipisfoldedout.Ifthisisnotthecase,youcanfoldouttheclipwithaat

screwdriver (Fig. 7).

3. Push the blade towards the machine to snap into place.

4. If the blade fails to engage, switch the appliance on (Fig. 3), then push the blade set against the

hand-held appliance until it audibly clicks into place and the blade moves (Fig. 8b).

Remove the attachment comb (Fig. 5) after every use and lift the blade set out of the casing (Fig. 6).

Use the cleaning brush to remove any cut hairs from the housing opening and from the blade set (Fig. 9).

Caution! Injuriesduetoincorrecthandling.

Thebladesetmustnotbeunscrewed.Thetopblademustnotbepushedoutcompletely!

• Push the top blade to the side (Fig. 9a) and remove cut hairs from the top and bottom blade using

the cleaning brush.

• After cleaning, return the top blade to its initial position (Fig. 9b). The top blade should be aligned in

the centre of the bottom blade. After cleaning the blade set, we recommend using hygienic spray.

Itkeepsallbladesetshygienicallycleanandiseectiveagainstbacteriaandviruses.

•

Oil the blade set with the blade set oil (Fig. 10).

• We recommend that you clean and care for your blade set during and after clipping.

• Re-attachthebladesetaftercleaning(Fig.7/8).Switchtheapplianceonbriey(approx.10

seconds)toensuretheoillmisevenlydistributed.

• For a good and long-lasting cutting performance, it is important to oil the blade set frequently.

• If the cutting performance deteriorates after long use despite regular cleaning and oiling, the blade

set should be replaced.

Cleantheairlterregularlytoensurethesupplyofair:

1. Detachtheltercoverusingabluntleverandremovefromthehousing(Fig.11a)

2. Cleantheairlterusingthecleaningbrush.

3. Pushtheltercoverintothehousinguntilitlocksintoposition(Fig.11b).

4. Only wipe the appliance with a soft, slightly damp cloth. Do not use solvents or abrasives.

PROBLEM ELIMINATION

Bladesetiscuttingbadlyorpullinghairout.

Cause: Blade set is dirty, worn out or blade is blunt.

• Clean and oil the blade set (Fig. 9/10);

if this does not resolve the problem, replace the blade set (Fig. 6/7/8).

Skininjury

Cause: Too much pressure on the skin.

• Reduce pressure when cutting close to skin.

Cause: Damaged blade set.

• Check whether the blade edges, or teeth are damaged and replace the blade set if necessary.

• NEVERuseadamagedbladeasthiswillcauseinjury.

Appliance is not working

Cause: Defective power supply.

• Make sure that contact between the mains and the socket is faultless. Check the mains cable for

possible damage.

In the event that this information does not help you resolve your problem,

please contact our Customer Service team. Never attempt to repair the appliance yourself!

Model: KM5 - WM6260 KM10 - WM6261

KM5 - CORDED DOG CLIPPER

KM10 - CORDED DOG CLIPPER

432

65 7

109

slide

Description of parts (Fig. 1)

A. Blade set

B. Release button for blade set

C. On/oswitch

D. Hang-up loop

E. Mains cable

F. Cleaning brush

G. Oil for blade set

H. Plug-in transformer

Mains Operation

1. Connect to the mains power supply (Fig. 2)

2. Switchontheapplianceusingtheon/oswitch(Fig.3a)andswitchoafteruse(Fig.3b).

The appliance has two speed settings.

Thesecanbeselectedviatheon/oswitch.

Setting I = slow speed

Setting II = high speed

Cutting with the attachment comb

The appliance can also be operated with attachment combs. Attachment combs can be used to extend

the cutting length range.

For best results we recommend using a #30 or #10 blade with the comb attachments.

Accessories are available from your local dealer.

Attaching / removing the attachment comb

1. Fit the attachment comb onto the bottom edge of the blade set (Fig. 4a) and push it over the cutting

edge of the bottom blade until it locks (Fig. 4b).

2. Push the attachment comb towards the cutting edge of the bottom blade (Fig. 5) and remove it from

the blade set.

Changing the blade set

To remove a blade set:

1. Switchotheapplianceusingtheon/oswitch(Fig.3).

2. Press the release button (B) (Fig. 6a) towards the blade set and lift the blade set away from the

housing (Fig. 6b).

3. Remove the blade set from the clip (Fig. 6c).

To attach a new blade set:

1. Attach the new blade set onto the clip (Fig. 8a).

2. Ensurethattheclipisfoldedout.Ifthisisnotthecase,youcanfoldouttheclipwithaat

screwdriver (Fig. 7).

3. Push the blade towards the machine to snap into place.

4. If the blade fails to engage, switch the appliance on (Fig. 3), then push the blade set against the

hand-held appliance until it audibly clicks into place and the blade moves (Fig. 8b).

Remove the attachment comb (Fig. 5) after every use and lift the blade set out of the casing (Fig. 6).

Use the cleaning brush to remove any cut hairs from the housing opening and from the blade set (Fig. 9).

Caution! Injuriesduetoincorrecthandling.

Thebladesetmustnotbeunscrewed.Thetopblademustnotbepushedoutcompletely!

• Push the top blade to the side (Fig. 9a) and remove cut hairs from the top and bottom blade using

the cleaning brush.

• After cleaning, return the top blade to its initial position (Fig. 9b). The top blade should be aligned in

the centre of the bottom blade. After cleaning the blade set, we recommend using hygienic spray.

Itkeepsallbladesetshygienicallycleanandiseectiveagainstbacteriaandviruses.

• Oil the blade set with the blade set oil (Fig. 10).

• We recommend that you clean and care for your blade set during and after clipping.

Model: KM5 - CORDED DOG CLIPPER WM6260

KM10 - CORDED DOG CLIPPER WM6261

• Re-attachthebladesetaftercleaning(Fig.7/8).Switchtheapplianceonbriey(approx.10

seconds)toensuretheoillmisevenlydistributed.

• For a good and long-lasting cutting performance, it is important to oil the blade set frequently.

• If the cutting performance deteriorates after long use despite regular cleaning and oiling, the blade

set should be replaced.

Cleantheairlterregularlytoensurethesupplyofair:

1. Cleantheairlterusingthecleaningbrush.

2. Only wipe the appliance with a soft, slightly damp cloth. Do not use solvents or abrasives.

PROBLEM ELIMINATION

Bladesetiscuttingbadlyorpullinghairout.

Cause: Blade set is dirty, worn out or blade is blunt.

• Clean and oil the blade set (Fig. 9/10);

if this does not resolve the problem, replace the blade set (Fig. 6/7/8).

Skininjury

Cause: Too much pressure on the skin.

• Reduce pressure when cutting close to skin.

Cause: Damaged blade set.

• Check whether the blade edges, or teeth are damaged and replace the blade set if necessary.

• NEVERuseadamagedbladeasthiswillcauseinjury.

Appliance is not working

Cause: Defective power supply.

• Make sure that contact between the mains and the socket is faultless. Check the mains cable for

possible damage.

In the event that this information does not help you resolve your problem,

please contact our Customer Service team. Never attempt to repair the appliance yourself!

Model: Power Grip - 8879

POWER GRIP CORDED DOG CLIPPER

1210

Description of parts (Fig. 1)

A Blade set

B Release button for blade set

C On/off switch (2 speed)

D Hang-up loop

E Mains cable

F Clip for blade set

G Replaceable drive lever tip

H Special tool

I Oil bottle

J Cleaning brush

Mains Operation

1. Before starting the appliance, always oil the blade set (Fig. 12).

2. Onlyconnecttheappliancetothesocketwhileitisswitchedo.

3. Connect the mains plug to the socket.

4. Switchontheapplianceusingtheon/oswitch(Fig.1).

5. Theapplianceisequippedwith2speedsettings.Thesecanbeselectedviatheon/oswitch.

Setting 1a = standard speed, setting 1b = high speed.

6. Afterusingtheappliance,switchitoandremovethemainsplug.

Cutting with the attachment comb

The appliance can also be operated with attachment combs. Attachment combs can be used to extend the

cutting length range. Accessories are available from your dealer.

For best results we recommend using a #30 or #10 blade with the comb attachments.

Accessories are available from your local dealer.

Attaching / removing the attachment combs

1. Fit the attachment comb onto the bottom edge of the blade set (Fig. 2a) and push it over the cutting

edge of the bottom blade until it locks (Fig. 2b).

2. Push the attachment comb towards the cutting edge of the bottom blade (Fig. 3) and remove it from

the blade set.

Changing the blade set

Replace a blunt or damaged blade set with an original spare part only. Spare parts can be ordered

through your dealer or Customer Services.

Beforereplacingthebladeset,switchtheapplianceo.

Lubricate the new blade set before attaching (Fig. 12).

Removing the blade set:

1. Press the release button (B) (Fig. 4a) towards the blade set and lift the blade set out of the housing

(Fig. 4b).

2. Lift the blade set out of its clip (Fig. 5) and ensure that the clip remains folded out.

Attaching the blade set:

1. Attach the new blade set onto the clip (Fig. 8a).

2. Ensurethattheclipisfoldedout.Ifthisisnotthecase,youcanfoldouttheclipwithaat

screwdriver (Fig. 7).

3. Push the blade towards the machine to snap into place.

4. If the blade fails to engage, switch the appliance on (Fig. 3), then push the blade set against the

hand-held appliance until it audibly clicks into place and the blade moves (Fig. 8b).

Replacing the drive lever tip

The drive lever tip (Fig. 9) is a wearable part. If necessary, it can be replaced in the following manner:

1. Remove blade set (Fig. 4/5).

2. Usingthespecialtool(H)provided,gripthetipandpullothedrivelever(Fig.10a).

3. Fitnewtiptodriveleverandpressdownrmlyuntilitengages(Fig.10b). For this task, only use the

special tool (H) provided.

Model: POWER GRIP - CORDED DOG CLIPPER - 8879

Cleaning and Care

• Disconnect from the mains before cleaning and maintaining the appliance.

• Donotimmersetheapplianceinwater!

• After each use, remove the hair clippings from the blade set with the cleaning brush.

• Only wipe the appliance with a soft cloth, which may be dampened slightly. Do not use

 solventsorabrasives!

• The blade set can be cleaned with hygienic spray.

• For a long-lasting, good cutting performance, it is important to oil the blade set frequently (Fig.

12).

• Only use Wahl blade oil.

• Blade set oil and hygienic spray are available from your dealer or our Customer Service team.

• We recommend oiling animal blades every 15 minutes during use.

• Remove the blade set (Fig. 4) and push the top blade to the side. Then remove cut hairs from the

top and bottom blade by using the cleaning brush (Fig. 11).

Importantnote:

Thetopblademustnotbepushedoutcompletely!Thebladesetmustnotbeunscrewed.

• After cleaning, return the top blade to its initial position.

• Oil the marked areas of the blade set with one drop of oil each (Fig. 12).

• The top blade should be aligned in the centre of the bottom blade.

• Reattachthebladesetasdescribedabove.Switchtheapplianceonbriey(approx.10seconds)to

• Ensuretheoillmisevenlydistributed.

• If the cutting performance deteriorates after long use despite regular cleaning and oiling, the blade

set should be replaced.

PROBLEM ELIMINATION

Bladesetiscuttingbadlyorpullinghairout.

Cause: Blade set is dirty, worn out or blade is blunt.

• Clean and oil the blade set (Fig. 9/10);

if this does not resolve the problem, replace the blade set (Fig. 6/7/8).

Skininjury

Cause: Too much pressure on the skin.

• Reduce pressure when cutting close to skin.

Cause: Damaged blade set.

• Check whether the blade edges, or teeth are damaged and replace the blade set if necessary.

• NEVERuseadamagedbladeasthiswillcauseinjury.

Appliance is not working

Cause: Defective power supply.

• Make sure that contact between the mains and the socket is faultless. Check the mains cable for

possible damage.

In the event that this information does not help you resolve your problem,

please contact our Customer Service team. Never attempt to repair the appliance yourself!

ARCO RECHARGEABLE DOG CLIPPER

Model: ARCO - WM6854

432

6 75

9 10

Model: ARCO RECHARGEABLE DOG CLIPPER - WM6854

Description of parts (Fig. 1)

A. Blade set

B. Cleaning lever

C. On/oswitch

D. Cutting-lengthadjustment

E. Battery charge indicator

F. Battery pack

G. Charging stand

H. Charging stand socket

I. Charging indicator

J. Interchangeable battery pack

K. Plug-in transformer

L. Appliance plug

M. Cleaning brush

N. Oil for blade set

* Attachment combs are optional accessories and can vary from model to model.

Chargingthebattery

This cordless hair clipper is supplied with two battery packs. While the appliance is in use, the second

battery pack can be recharged on the charging stand. This means that the clipper is always ready for use.

Before the appliance is used for the rst time, each battery pack should be charged for approx 90 minutes.

1. Connect the appliance plug (L) on the plug-in transformer to the charging stand socket (H) (Fig. 2a).

2. Connect the plug-in transformer to the mains socket (Fig. 2b).

3. Insert the battery pack into the recess of the charging stand (Fig. 4). The charging process starts.

During charging, the red charging indicator (I) is illuminated.

• It should take around 75 minutes for the appliance to charge to full capacity.

• The second battery can remain in the charging stand so that a charged battery pack is always

available.

4. Oncechargingiscomplete,thechargingindicator(I)onthechargingstand(G)willstartashing.

BatteryOperation

1. Switchontheapplianceusingtheon/oswitchandswitchoafteruse(Fig.5a/b).

• Whenyoupresstheon/oswitch,thebatterypowerindicator(E)willlightupbrieytoindicatethat

the appliance is ready for use.

• The appliance can be operated for up to 80 minutes when the battery is fully charged.

• Insucientmaintenanceofthebladesetcansignicantlyreducetheoperatinglife.

• If the battery power indicator (E) on the hand-held appliance lights up during operation, this means

there is only approx. 15% battery power remaining. The battery pack needs to be recharged.

You can now use the charged replacement battery pack.

Torechargethebattery:

1. Switchotheapplianceusingtheon/oswitch(Fig.5b).

2. Press the unlock buttons on the side and remove the battery pack (Fig. 3a).

3. Remove the charged battery pack (Fig. 4) and push it into the appliance until you hear it snap into

place (Fig. 3b).

4. Fittheatbatterypacktothechargingstand(Fig.4).SeeChargingthebattery

OPERATION

Setting the cutting length

Thecuttinglengthcanbeadjustedtobetween0.7mmand3mm(5possiblepositions)usingthecutting-

lengthadjustmentintegratedintothebladeset(Fig.6).

Cutting with attachment combs

The appliance can also be operated with attachment combs. In order to achieve the indicated cutting

length,thecuttinglengthadjustmentlevershouldbesettopositionI(Fig.6).

Attaching/removing the attachment comb

1. Slide the attachment comb on to the blade set in the direction of the arrow until it reaches the

limit (Fig. 7a).

2. The attachment comb can be removed by pushing it in the direction of the arrow (Fig. 7b).

Maintenance, cleaning and care.

• Remove the attachment comb (Fig. 7b) after every use and lift the blade set out of the housing (Fig.

8a).

• Use the cleaning brush to remove any cut hairs from the housing opening and from the blade set

(Fig. 9).

• The cleaning lever (Fig. 9b) can also be pressed. This allows the cut hairs that accumulate between

the bottom blade and the top blade to be easily removed using the cleaning brush.

• Only wipe the appliance with a soft, slightly damp cloth

• The charging contacts on the charging stand and on the battery pack should always be kept clean.

• Clean the blade set regularly using hygienic spray.

• Oil the blade set with the blade set oil (Fig. 10)

• For long-lasting cutting performance, it is important to oil the blade set frequently.

• If the cutting performance deteriorates after long use despite regular cleaning and oiling, the blade

set should be replaced.

Changing the blade set

Removing the blade set:

1. Switchtheapplianceousingtheon/oswitch(Fig.5b)anddisconnectfromthepowersupply.

2. Slidethebladesetothehousinginthedirectionofthearrow(Fig.8a).Removethebladeset.

Replacing the blade set:

1. Replace the blade set by hooking it into the housing. The small lug at the base of the blade should

be aligned with the indent on the clipper casing. Press the blade down until it clicks into position

(Fig. 8b).

Problem elimination

Bladesetiscuttingbadlyorpullinghairout.

Cause: Blade set is dirty, worn or blunt.

• Clean and oil the blade set (Fig. 9/10); if this does not resolve the problem, replace the blade set

(Fig. 8).

Skininjury

Cause: Too much contact pressure on the skin.

• Reduce contact pressure when cutting close to skin.

Cause: Damaged blade set.

• Check whether the blade edges or teeth are damaged and replace the blade set if necessary.

• NEVERuseadamagedbladeasthiswillcauseinjury.

Batterylifeistooshort.

Cause: Blade set and housing opening are dirty.

• Clean and oil the blade set (Fig. 9/10).

Cause: Battery is worn out.

• Replace the battery pack with an original spare part.

• Replacement battery packs are available from your dealer or from our Customer Service team.

Charging indicator does not light up.

Cause: The battery pack is not correctly positioned on the charging stand.

• Ensure that the battery pack has been correctly placed on the charging stand.

Cause: Charging contacts are dirty.

• Clean the charging contacts on the charging stand and on the battery pack

Cause: Defective power supply.

• Ensure that the plug-in transformer is plugged into the mains socket.

• Check the mains cable for possible damage.

BatteryRemoval,DisposalandReplacement

For Removal instructions see page 33

> 80%

50 - 30%

80 - 65%

30 - 10%

65 - 50%

10 - 0%

BRAVURA CORD /CORDLESS DOG CLIPPER

Model: BRAVURA - WM6870

432

65 7

8 9

Description of parts (Fig. 1)

A. Blade set

B. On/oswitch

C. Battery power indicator

D. Charging stand

E. Cutting-lengthadjustment

F. Appliance socket

G. Charging stand socket

H. Plug-in transformer

I. Appliance plug

J. Cleaning brush

K. Oil for blade set

* Attachment combs are optional accessories and can vary from model to model.

Chargingthebattery

1. Connect the appliance plug (I) on the plug-in transformer to the charging stand socket (G)

(Fig. 4a).

• The appliance can also be connected directly to the plug-in transformer for charging (Fig. 2a/b).

• Battery overcharging is prevented thanks to intelligent charge management.

2. Connect the plug-in transformer to the mains socket (Fig. 4a).

3. Switchotheapplianceusingtheon/oswitch(Fig.3a).

4. Place appliance on the charging stand (Fig. 4) or connect directly to the plug-in transformer (Fig.

2a/b). A signal will sound and the charging process begins.

5. Depending on the charge status, the corresponding segment of the battery power indicator will

ashduringthechargingprocess.Oncethebatteryisfullycharged,allsegmentsofthebattery

power indicator will remain lit continuously.

6. After the appliance has been removed from the charging stand, the display goes out after approx.

30 seconds (power saving mode).

7. It should take around 60 minutes for the appliance to charge to full capacity.

8. Once the battery is fully charged, a signal will sound

BatteryOperation

1. Switchontheapplianceusingtheon/oswitchandswitchoafteruse(Fig.3a/b).

• Aftertheappliancehasbeenswitchedo,thedisplaygoesoutabout30secondslater(power

saving mode).

• When the battery is fully charged, the appliance can be used for up to 90 minutes without mains

connection.

• The charge status of the battery is displayed by the battery power indicator (C).

Whenthebatteryhasfullyrundown,theapplianceswitchesitselfoautomatically.

• Incaseofinsucientmaintenanceofthebladeset,theoperatingtimecanbereduced

considerably.

Mains Operation

1. Connect the appliance plug (I) on the plug-in transformer to the appliance socket (F) (Fig. 2a).

2. Connect the plug-in transformer to the mains socket (Fig. 2b).

3. Switchontheapplianceusingtheon/oswitchandswitchoafteruse(Fig.3a/b). 

OPERATION

Setting the cutting length

Thecuttinglengthcanbeadjustedtobetween0.7mmand3mm(5possiblepositions)usingthecutting-

lengthadjustmentintegratedintothebladeset(Fig.5).

Cutting with attachment combs

The appliance can also be operated with attachment combs.

Inordertoachievetheindicatedcuttinglength,thecuttinglengthadjustmentlevershouldbesetto

position 1 (Fig. 5).

Model: BRAVURA CORD / CORDLESS CLIPPER - WM6870

Attaching/removing the attachment comb

1. Slide the attachment comb on to the blade set in the direction of the arrow until it reaches the limit

(Fig. 6a).

2. The attachment comb can be removed by pushing it in the direction of the arrow (Fig. 6a).

Maintenance, cleaning and Care.

• Remove the attachment comb (Fig. 6b) after every use and lift the blade set out of the housing (Fig.

7a).

• Use the cleaning brush to remove any cut hairs from the housing opening and from the blade set

(Fig. 8).

• The cleaning lever (Fig. 8b) can also be pressed. This allows the cut hairs that accumulate between

the bottom blade and the top blade to be easily removed using the cleaning brush.

• Only wipe the appliance with a soft, slightly damp cloth

• Oil the blade set with the blade set oil (Fig. 9)

• For good and long-lasting cutting performance, it is important to oil the blade set frequently.

• If the cutting performance deteriorates after long use despite regular cleaning and oiling, the blade

set should be replaced.

Automaticsensorsystem

To give you advance notice of an urgent need for maintenance care, your hair cutting appliance has been

equipped with an automatic sensor system.

• The sensor system automatically recognises when the blade set needs oiling or cleaning.

• Aftertheapplianceisswitchedo,anacousticsignalwillsoundandthebatterypowerindicatorwill

ashfor2minutes.

• Theacousticsignalandtheashingofthebatterypowerindicatorcanbecancelled(turnedo)by

brieyswitchingtheapplianceonando.

• Before using the appliance again, it is strongly recommended to clean the appliance and oil the

blade set. See section Maintenance, Cleaning and care.

• Failure to observe these instructions may result in damage to and early failure of the appliance,

which will void all guarantee claims.

Changing the blade set

Removing the blade set:

1. Switchtheapplianceousingtheon/oswitch(Fig.3a)anddisconnectfromthepowersupply.

2. Slidethebladesetothehousinginthedirectionofthearrow(Fig.7a).Removethebladeset.

Replacing the blade set:

1. Replace the blade set by hooking it into the housing. The small lug at the base of the blade should

be aligned with the indent on the clipper casing. Press the blade down until it clicks into position

(Fig. 7b).

Problem elimination

Bladesetiscuttingbadlyorpullinghairout.

Cause: Blade set is dirty or worn.

• Clean and oil the blade set (Fig.8/9); if this does not resolve the problem, replace the blade set

(Fig. 7).

Batterylifeistooshort.

Cause: Blade set and housing opening are dirty.

• Clean and oil the blade set (Fig. 8/9).

Abladesetthatisverydirtyandhasnotbeenoiledcanhalvetheavailablebatterylife!Ifthe

blade set is clean and oiled and the battery life is still far too short, it is likely that the batteries are

nearing the end of their life.

• Battery life generally decreases at a steady rate when the appliance is used on a day-to-day

basis. The batteries used here are specially designed for professional and everyday use, but are

alsoaectedbythis.

Batterypowerindicatorlightdoesnotlightup.

Cause: Appliance has not been correctly placed on the charging stand

• Ensure that the hand-held appliance has been correctly placed on the charging stand.

Cause: Defective power supply.

• Ensure that the plug-in transformer is plugged into the mains socket.

• Check the mains cable for possible damage.

• Check the power supply.

Entirebatterypowerindicatorisashing

• Check whether the blade set is blocked and the blade is able to move.

• Switchtheapplianceonando.Iftheentiredisplayisashing,pleasecontactyourspecialistretaileror

the Wahl Customer Service team.

Batterypowerindicatorlightdoesnotlightup.

Cause: Appliance has not been correctly placed on the charging stand.

BatteryRemoval,DisposalandReplacement

For removal instructions see page 33

Skininjury

Cause: Too much contact pressure on the skin.

• Reduce contact pressure when cutting close to skin.

Cause: Damaged blade set.

• Check whether the blade edges or teeth are damaged and replace the blade set if necessary.

• NEVERuseadamagedbladeasthiswillcauseinjury.

BRAVMINI RECHARGEABLE DOG TRIMMER

Model: BRAVMINI - WM6590

5 6

Description of parts (Fig. 1)

A. Blade set

B. On/oswitch

C. Charging indicator

D. Charging stand

E. Charging stand socket

F. Oil for blade set

G. Cleaning brush

H. Attachment comb

I. Plug-in transformer

J. Appliance plug

*Beforetheapplianceisusedforthersttimeitshouldbechargedfor16 hours.

ChargingtheRechargeableBattery

1. Connect the appliance plug (J) on the plug-in transformer to the charging stand socket (E) (Fig. 2a).

Battery overcharging is prevented thanks to intelligent charge management.

2. Connect the plug-in transformer to the mains socket (Fig. 2a).

3. Switchotheapplianceusingtheon/oswitch(Fig.3a).

4. Place the appliance on the charging station (Fig. 2) · During charging, the charging indicator (C) is

illuminated.

• After the appliance has been removed from the charging stand, the display goes out.

• It takes no more than 16 hours for the appliance to charge to full capacity.

BatteryOperation

1. Switchontheapplianceusingtheon/oswitchandswitchoafteruse(Fig.3a/b).

• With the battery fully charged, the appliance can be operated for up to 100 minutes. This

capacityisattainedafterapprox.5-10chargingcycles.Incaseofinsucientmaintenanceof

the blade set, the operating time can be reduced considerably.

OPERATION

Cutting with the attachment comb

The appliance can also be operated with an attachment comb. The attachment comb has 5 indent

positionsforadjustingthelengthofcutThefurthertheattachmentcombispushedin(retracted),the

shorterthelengthofcut.Thelengthofcutcanbeadjustedfrom3mm(Fig.5a)to6mm(Fig.5b).

Attachment Comb

Attaching/removing the attachment comb

1. Slide the attachment comb on to the blade set in the direction of the arrow until it reaches the limit

stop (Fig. 4a).

2. The attachment comb can be removed by pushing it in the direction of the arrow (g4b)

If the cutting performance deteriorates after long use despite regular cleaning and oiling, the blade set

should be replaced.

Changing the blade set

Removing the blade set:

1. Switchtheapplianceousingtheon/oswitch(Fig.3a)anddisconnectfromthepowersupply.

2. Slidethebladesetothehousinginthedirectionofthearrow(Fig.6a).Removethebladeset.

Replacing the blade set:

1. Replace the blade set by hooking it into the housing. The small lug at the base of the blade should

be aligned with the indent on the clipper casing. Press the blade down until it clicks into position

(Fig. 6b).

BatteryRemoval,DisposalandReplacement

For removal instructions see page 33

Model: BRAVMINI RECHARGEABLE DOG TRIMMER - WM6590

432

65 7

MINI ARCO CORD /CORDLESS DOG TRIMMER

Model: MINI ARCO - WM6565

Description of parts (Fig. 1)

A. Blade set

B. On/oswitch

C. Charging indicator light

D. Appliance socket

E. Attachment comb small = cutting lengths 3 mm and 6 mm

F. Attachment comb large = cutting lengths 9 mm and 12 mm

G. Cleaning brush

H. Oil for blade set

I. Plug-in transformer

J. Appliance plug

Chargingthebattery

Beforetheapplianceisusedforthersttimeitshouldbechargedfor2hours.

1. Connect the appliance plug (J) on the plug-in transformer to the appliance socket (D) (Fig. 2).

Battery overcharging is prevented thanks to intelligent charge management.

2. Connect the plug-in transformer to the mains socket

3. Switchotheapplianceusingtheon/oswitch(Fig.3b).

 •Duringcharging,thechargingindicator(C)ashesatevenlyspacedintervals.Whenthebatteryis

fullycharged,thechargingindicatorashesatadierentrate(16on/1o).

• It should take around 2 hours for the appliance to charge to full capacity

BatteryOperation

1. Switchontheapplianceusingtheon/oswitchandswitchoafteruse(Fig.3a/b).

• When the battery is fully charged, the appliance can be used for up to 100 minutes without mains

connection. This capacity is attained after approx. 5 - 10 charging cycles.

• Insucientmaintenanceofthebladesetwillreduceoperatingtimeconsiderably.

Mains Operation

1. Connect the appliance plug (J) on the plug-in transformer to the appliance socket (D) (Fig. 2).

2. Insert the plug-in transformer into the mains socket.

3. Switchontheapplianceusingtheon/oswitchandswitchoafteruse(Fig.3a/b).

OPERATION

Cutting with the attachment comb

The appliance can also be operated with attachment combs. The following attachment combs are

included as standard:

• Attachment comb small = cutting lengths 3 mm and 6 mm

• Attachment comb large = cutting lengths 9 mm and 12 mm

• The cutting length (in mm) is shown on the attachment comb.

• Oneattachmentcombcanbeusedfortwodierentcuttinglengths.Forthesecondcuttinglength,all

you need to do is remove the attachment comb, rotate and replace.

• The advantage of these attachment combs is that no matter the angle at which you approach the hair,

you always achieve the same cutting length.

Attaching/removing the attachment comb

1. Place the attachment comb onto the cutting edge of the blade set and press it down onto the blade set

into the knobs in the direction of the housing until it clicks into position (Fig. 4a).

2. The attachment comb can be removed by pushing it in towards the cutting edge (Fig. 4b).

Changing the blade set

Removing the blade set:

1. Switchtheapplianceousingtheon/oswitch(Fig.3b)anddisconnectfromthepowersupply.

2. Slidethebladesetothehousinginthedirectionofthearrow(Fig.5a).Removethebladeset.

Replacing the blade set:

1. Replace the blade set by hooking it into the housing. The small lug at the base of the blade should

be aligned with the indent on the clipper casing. Press the blade down until it clicks into position

(Fig. 5b).

BatteryRemoval,DisposalandReplacement

For removal instructions see page 33

Model: MINI ARCO CORD / CORDLESS DOG TRIMMER - WM6565

STAINLESS STEEL BLADES AND ATTACHMENT COMBS

10 11 12 13 14

6 7

Cutting lengths

10mm

8mm

6mm

4mm

3mm

2mm

1.8mm

1.5mm

0.8mm

0.6mm

0.4mm

1854 Standard

1854 Course

Diamond

(#3F)

(#4)

(#4F)

(#5)

(#5F)

(#7)

(#7F)

(#8.5)

(#9)

#10)

(#15)

(#30)

(#40)

(#50)

42mm

0.7 - 3mm

Competition Blade Comb Attachments

Competition Series Blades

Arco/Bravura comb attachments

Arco/Bravura Blades

3mm

6mm

10mm

13mm

16mm

19mm

22mm

25mm

RED

PURPLE

BLUE

ORANGE

YELLOW

LAVENDER

GREEN

LIGHT BLUE

# NAME LENGTH COLOUR

3mm

6mm

10mm

13mm

16mm

19mm

22mm

25mm

RED

PURPLE

BLUE

ORANGE

YELLOW

LAVENDER

GREEN

LIGHT BLUE

# NAME LENGTH COLOUR

MINI ARCO - WM6565

BRAVMINI - WM6590

For battery replacement the entire, intact trimmer should be sent to: Wahl (UK) Ltd Customer Services

(theaddresscanbefoundonthereverseofthisbooklet)ortakentoasuitablyqualiedprofessional.The

battery should only be replaced by the original manufacturers spare.

BatteryRemovalandDisposal

At the end of its life, when it will no longer take a full charge, the battery in your trimmer must be removed

andrecycled/disposedofcorrectly.Batteriesshouldbedisposedofatanocialcollectionpoint.Ifyou

are having trouble removing the battery you can also return the product to Wahl (UK) Ltd Customer

Services who will dispose of it in an environmentally safe way.

To remove the battery follow these steps:

1. Unplug the transformer from the outlet, disconnect from trimmer and allow the

batteries to completely run down before disassembly.

2. Remove the Blade

3. Using a Torx 7 screwdriver, remove the 2 screws found under the blade

4. PrizetheTrimmerapartalongthejoininthehousing

5. Remove the motor and PCB assembly

6. Remove the battery by prizing up from the PCB (be careful not to puncture the battery)

7. Apply tape to both ends of the battery before recycling/disposing.

Replacement batteries can be ordered from: Wahl (UK) Ltd Customer Services (the address can be

found on the reverse of this booklet). The battery should only be replaced by the original manufacturers

spare.

ARCO - WM6565

BatteryRemovalandDisposal

At the end of its life, when it will no longer take a full charge, the battery in your clipper must be removed

andrecycled/disposedofcorrectly.Batteriesshouldbedisposedofatanocialcollectionpoint.Ifyou

are having trouble removing the battery you can also return the product to Wahl (UK) Ltd Customer

Services who will dispose of it in an environmentally safe way.

To remove the battery follow these steps:

1. Allow the batteries to completely run down before removing.

2. Press the clips on each side of the battery and remove.

3. Apply tape to over the contacts of the battery before recycling/disposing.

Bravura - WM6870-803

LithiumBatteryReplacement,RemovalandDisposal

For battery replacement the entire, intact clipper or trimmer should be sent to: Wahl (UK) Ltd Customer

Services(theaddresscanbefoundonthereverseofthisbooklet)ortakentoasuitablyqualied

professional. The battery should only be replaced by the original manufacturers spare, for safety reasons

a substitute should not be used.

Donotattempttoremovethebattery.Lithium-Ionbatteriescanexplode,catchre,and/orcauseburnsif

disassembled, damaged or exposed to water or high temperatures.

Lithium Battery Disposal

Do not dispose of this product or the Lithium battery in the normal household waste.

TheproductshouldbereturnedtoWahlCustomerServiceswhereweoeratakebackserviceortaken

to a local collection facility where they will be dealt with safely and sent for the appropriate recycling.

BATTERY REPLACEMENT, REMOVAL AND DISPOSAL

WIRING - Max 45 - KM6245 / WM6245

WARNING: If the supply cord is damaged it must be replaced by the manufacturers service agent or a

similarlyqualiedpersoninordertoavoidahazard.

The wires in the mains lead are coloured in accordance to the following code:

Blue Neutral (N) Brown live (L)

Thisapplianceisttedwitha3pinplugwhichhasa3ampfusetted.

Iftheplugsuppliedisnotsuitableforyoursocketorbecomesdamaged,itshouldbecutoanddisposed

of,andasuitableplugttedasdetailedbelow.

As the colours of the wires in the mains lead of this appliance may not correspond with the colour

markings identifying the terminals in your plug, proceed as follows.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the

letter ‘N’ or coloured BLACK or BLUE.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with

the letter ‘L’ or coloured RED or BROWN.

DO NOT connect either wire to the terminal in the plug which is marked with the letter ‘E’ or has the Earth

symbol, or coloured GREEN or GREEN/YELLOW.

Ifa13amp(BS1363)plugisused,a3ampfusemustbetted.Ifanyothertypeofplugisuseda5amp

fusemustbettedeitherintheplugoradaptoratthedistributionboard.Replacementfusesshouldbe

approved to BS 1362

Fusecovermustberettedwhenchangingthefuse.Ifthefusecoverislosttheplugmustnotbeused

until a replacement is obtained. Information for obtaining the correct fuse is marked on the carrier itself

and in the bottom of the fuse cavity in the plug. These may be obtained from Wahl (UK) Ltd.

KM5 - WM6260

KM10 - WM6261

Power Grip - 8879

WARNING:If the transformer is damaged it must be replaced by the manufacturers service agent or a

similarlyqualiedpersoninordertoavoidahazard.Thisproductmustonlybeusedwithtransformer

supplied. Should a replacement be required contact Wahl (UK) Ltd customer services.

WIRING - Arco - WM6854

Bravura - WM6870

BravMini - WM6590

Mini Arco - WM6565

WARNING: If the transformer is damaged it must be replaced. This product must only be used with the

transformer supplied. Should a replacement be required contact Wahl (UK) Ltd customer services.

WIRING AND DISPOSAL

DISPOSAL

Handle with care! Environmental damage in the case of incorrect disposal.

Correct disposal will ensure environmental protection and prevent any potentially harmful impacts on

people and the environment.

Adhere to the relevant legal requirements when disposing of the appliance.

InformationonthedisposalofelectricalandelectronicappliancesintheEuropeanCommunity:

WithintheEuropeanCommunity,nationalregulationsarespeciedforthedisposalofelectrical

appliances, based on EU Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE).

In accordance with this, the appliance can no longer be disposed of with the local or domestic waste.

The appliance will be accepted free of charge by local collection points or recycling centres.

The packaging for this product is made from recyclable materials. Dispose of this in an environmentally

friendly manner by recycling it. Information on the disposal of electrical and electronic appliances in the

European Community:

WEEE

WASTE ELECTRICAL & ELECTRONIC EQUIPMENT DIRECTIVE 2002/96/EC (WEEE)

At the end of this products life it should not be disposed of with general household waste.

Care should be taken to dispose of in a suitable manner in accordance with your Local Authority regulation

GUARANTEE

This product is guaranteed against defects in material and workmanship for a period of 2 years from the

date of original purchase or receipt as a gift.

The guarantee becomes invalid in the case of misuse or repair by unauthorised persons.

Should this product become defective during the warranty period, return it to the store of purchase

together with your proof of purchase for repair or replacement without any charges to you.

ThisguaranteeinnowayaectsyourrightsunderstatutorylawintheUnitedKingdom.

GENERAL CLEANING

Aggressive chemicals could damage the appliance and accessories

• Never use solvents or scouring agents.

• Only use cleaning agents and blade set oil recommended by the manufacturer.

• Hygienic spray and blade set oil are available from your dealer or our Customer Service Team.

Never immerse the appliance in water.

Remove the attachment comb after each use and clean the blade set using the cleaning brush.

Remove the blade set and clean the blade. Remove any hairs and dirt between top and bottom blade with

the cleaning brush.

The appliance must be kept clean. Use only a slightly damp cloth for cleaning the housing and charging

stand if applicable. Never use solvents or scouring agents.

Oil the blade set regularly using the oil supplied to maintain the cutting performance and ensure a long

service life. Replace the attachment comb to protect the blade when not in use.

The blade set should be replaced if cutting performance is reduced after extended use.

WAHL (UK) LTD

Sterling House

Clipper Close

Ramsgate

Kent

CT12 5GG

Customer Services

T: 01227 740066

W: www.wahl.co.uk

E: customer[email protected]

Form No. ZB642

Rev.2 09-18