Criteria for Evaluation of Nuclear Facility Training Programs

NOT MEASUREMENT

SENSITIVE

DOE-STD-1070-94

Reaffirmed

July 2014

DOE STANDARD

CRITERIA FOR EVALUATION OF NUCLEAR

FACILITY TRAINING PROGRAMS

(Formerly Titled: Guidelines for Evaluation of Nuclear

Facility Training Programs)

U.S. Department of Energy FSC-6910

Washington, D.C. 20585

DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.

DOE-STD-1070-94

This document is available on the

Department of Energy Technical Standards Program Web page at

http://www.hss.doe.gov/nuclearsafety/ns/techstds/

DOE-STD-1070-94

TABLE OF CONTENTS

PARAGRAPH PAGE

FOREWORD ......................................................................................................................... iv

1. SCOPE ............................................................. 1

1.1 Purpose ........................................................................................ 1

1.2 Applicability ........................................................................................ 1

2 . APPLICABLE DOCUMENTS ..................................................................... 2

2.1 Government Documents. ............................................................................. 2

2.2 Non-Government Documents. ...................................................................... 5

3. DEFINITIONS ...................................................................... 7

4 . INTRODUCTION ........................................................................ 7

5 . THE EVALUATION PROCESS ................................................................. 7

5.1 Benefits of Evaluations .................................................................................... 7

5.2 Evaluator Qualifications ............................................................................... 8

5.3 Evaluation Methods .......................................................................................... 9

5.4 Evaluation Frequency. ................................................................................ 11

5.5 Graded Approach. ................................................................................ 12

6 . APPLICATION OF OBJECTIVES AND CRITERIA ......................................... 12

7 . REPORTING EVALUATION RESULTS .................................................. 14

8 . TRACKING EVALUATION RESULTS .................................................. 16

APPENDIX - OBJECTIVES AND CRITERIA .................................................................. 17

Objective 1 Management/Administration of Training and Qualification Programs 19

Objective 2 Development and Qualification of Training Staff ..................................... 23

Objective 3 Trainee Entry-level Requirements ........................................................... 25

Objective 4 Determination of Training Program Content ............................................ 27

Objective 5 Design and Development of Training Programs ..................................... 29

Objective 6 Conduct of Training ................................................................................. 33

Objective 7 Trainee Examinations and Evaluations ................................................... 35

Objective 8 Training Program Evaluation ................................................................... 39

iii



DOE-STD-1070-94

FOREWORD

This DOE Technical Standard is invoked as a requirement by DOE Order 426.2, Personnel

Selection, Training, Qualifications and Certification Requirements for DOE Nuclear Facilities,

dated 4-21-2010, by the following statements:

1) “Heads of field organizations/field element manager for NNSA operations or

designee must evaluate contractor training and qualification programs using the

methodology described in DOE-STD-1070-94, Guidelines for Evaluation of Nuclear

Facility Training Programs.” [Section 4.c];

2) “Heads of field organizations must ensure that the entire scope of DOE-STD-1070-94

that is applicable to their site is addressed (either through contractor or federal

reviews) at least once in each three year interval. ” [Section 4.c.(3)]; and

3) “Contractors must perform periodic systematic evaluations of training and

qualification programs (not to exceed three years) in accordance with DOE-STD-

1070-94, Guidelines for Evaluation of Nuclear Facility Training Programs. ”

[Attachment 1, Chapter I, Section 4.a.(3)].

The Department of Energy (DOE)

Criteria for Evaluation of Nuclear Facility Training

Programs

establishes a single set of objectives and criteria for the evaluation of training

programs developed to meet the requirements of DOE Order 426.2 and other directives that

address training and qualification. For the purpose of this standard, evaluation includes

appraisals, surveillances, audits, reviews, assessments, and other activities intended to

evaluate training. The standard is intended to assist personnel in performing evaluations of

training and qualification programs. It should be used in conjunction with other regulations,

policies, or directives that require the evaluation of training and qualification programs.

Throughout this Standard, the word “shall" denotes actions that are required to comply with

this Standard. The word "should" is used to indicate recommended practices. The use of

"may" with reference to application of a procedure or method, indicates that the use of the

procedure or method is optional.

DOE-STD-1070-94

1. SCOPE

1.1 Purpose. The Criteria for Evaluation of Nuclear Facility Training Programs

establishes objectives and criteria for evaluating nuclear facility training programs. The

methodology in this standard provides a framework for the systematic evaluation of training

programs at nuclear facilities and is based, in part, on established criteria for Technical

Safety Appraisals, Tiger Team Assessments, commercial nuclear industry evaluations, and

the DOE Training Accreditation Program.

1.2 Applicability. This standard applies to organizations or persons involved in

evaluating training methods, materials, and programs at DOE nuclear facilities. DOE

nuclear facilities include Category A reactor facilities, Category B reactor facilities, and non-

reactor nuclear facilities. The focus of the standard is evaluations that are conducted by

DOE field organizations (Operations Office, Area Office, or Project Office as appropriate). It

should also be used by others who conduct reviews of training, both internal and external to

the Department.

Training programs will vary according to the complexity and hazard potential of a particular

nuclear facility. Consequently, certain criterion may not be applicable to low-hazard

facilities; hence, a degree of flexibility shall be used when applying the criterion. When a

criterion is not applicable, it need not be considered.

While this standard assumes specific methods of evaluation, alternate methods that

are consistent with overall organizational needs, policies, and resources are

acceptable.

DOE-STD-1070-94

2. APPLICABLE DOCUMENTS

2.1 Government Documents.

2.1.1 DOE Orders, Standards, and Guidelines Applicable to Standard

Development. The following DOE Orders, standards, manuals, and guidelines were

used in the development of this document.

DOE O 426.2, PERSONNEL SELECTION, TRAINING, QUALIFICATION, AND

CERTIFICATION REQUIREMENTS FOR DOE NUCLEAR FACILITIES, which

establishes requirements for development and implementation of qualification programs

for personnel involved in the operation, maintenance, and technical support of DOE

nuclear facilities.

DOE-HDBK-1074-95, ALTERNATIVE SYSTEMATIC APPROACHES TO TRAINING,

which provides guidance on how to select and implement appropriate training

processes considering job complexity, hazard potential, and available training media.

2.1.2 DOE Standards that Assist in Meeting the Objectives and Criteria. The

following DOE standards provide guidance and good practices to assist in meeting

the objectives and criteria contained in the Appendix to this standard.

DOE-HDBK-1001-96, GUIDE TO GOOD PRACTICES FOR TRAINING AND

QUALIFICATION OF INSTRUCTORS, which provides guidance for the development

of initial and continuing instructor training programs. This guide will assist in meeting

Objective 2, Development and Qualification of Training Staff.

DOE-HDBK-1002-96, GUIDE TO GOOD PRACTICES FOR TRAINING AND

QUALIFICATION OF CHEMICAL OPERATORS, which provides guidance for the

development of new training programs or the refinement of existing training programs

for chemical operators. This guide will assist in meeting Objective 4, Determination of

Training Program Content.

DOE-STD-1070-94

DOE-HDBK-1003-96, GUIDE TO GOOD PRACTICES FOR TRAINING AND

QUALIFICATION OF MAINTENANCE PERSONNEL, which provides guidance for the

development of new training programs or the refinement of existing training programs

for maintenance personnel. This guide will assist in meeting Objective 4, Determination

of Training Program Content.

DOE-HDBK-1200-97, GUIDE TO GOOD PRACTICES FOR DEVELOPING LEARNING

OBJECTIVES, which provides information and guidance for the development of

learning objectives. This guide will assist in meeting Objective 5, Design and

Development of Training Programs; specifically Criterion 5.1.

DOE-HDBK-1201-97, GUIDE TO GOOD PRACTICES: EVALUATION INSTRUMENT

EXAMPLES, which provides examples of various methods and techniques for

developing evaluation instruments. This guide will assist in meeting Objective 7,

Trainee Examinations and Evaluations.

DOE-HDBK-1202-97, GUIDE TO GOOD PRACTICES FOR TEAMWORK TRAINING

AND DIAGNOSTIC SKILLS DEVELOPMENT, which provides guidance for the

development, implementation, and improvement of training on teamwork and

diagnostics. This guide will assist in meeting Objective 6, Conduct of Training;

specifically Criterion 6.2.

DOE-HDBK-1203-97, GUIDE TO GOOD PRACTICES FOR TRAINING OF

TECHNICAL STAFF AND MANAGERS, which provides guidance for the design and

development of technical staff and managers' initial and continuing training programs.

This guide will assist in meeting Objective 4, Determination of Training Program

Content; specifically Criteria 4.2 and 4.3.

DOE-HDBK-1204-97, GUIDE TO GOOD PRACTICES FOR THE DEVELOPMENT OF

TEST ITEMS, which provides guidance for the systematic development of valid and

reliable examinations. This guide will assist in meeting Objective 7, Trainee

Examinations and Evaluations; specifically Criteria 7.1 and 7.2.

DOE-STD-1070-94

DOE-HDBK-1205-97, GUIDE TO GOOD PRACTICES FOR THE DESIGN,

DEVELOPMENT, AND IMPLEMENTATION OF EXAMINATIONS, which provides

guidance for the construction and administration of written, oral, and performance

examinations. This guide will assist in meeting Objective 7, Trainee Examinations

and Evaluations; specifically Criteria 7.1 and 7.2.

DOE-HDBK-1206-98, GUIDE TO GOOD PRACTICES FOR ON-THE-JOB TRAINING,

which provides guidance for the design and development of on-the-job training (OJT)

programs and for instructors who conduct OJT and performance examinations. This

guide will assist in meeting Objective 6, Conduct of Training; specifically Criterion 6.3.

DOE-HDBK1114-98, GUIDE TO GOOD PRACTICES FOR LINE AND TRAINING

MANAGER ACTIVITIES RELATED TO TRAINING AND QUALIFICATION, which

provides guidance for line and training managers relative to participation in and

evaluation of the facility's training and qualification programs. This guide will assist in

meeting Objective 1, Management and Administration of Training and Qualification

Programs.

DOE-HDBK-1115-98, GUIDE TO GOOD PRACTICES FOR THE SELECTION,

TRAINING, AND QUALIFICATION OF SHIFT TECHNICAL ADVISORS, which

provides guidance for the design and development of a shift technical advisor (STA)

training program. This guide will assist in meeting Objective 4, Determination of

Training Program Content.

DOE-HDBK-1116-98, GUIDE TO GOOD PRACTICES FOR DEVELOPING AND

CONDUCTING CASE STUDIES, which provides guidance for the design,

development, and conduct of case studies for use in the training program. This guide

will assist in meeting Objective 5, Design and Development of Training Programs.

DOE-HDBK-1117-99, GUIDE TO GOOD PRACTICES FOR MAINTENANCE

SUPERVISOR SELECTION AND DEVELOPMENT, which provides guidance for the

design and development of maintenance supervisor training programs. This guide will

assist in meeting Objective 4, Determination of Training Program Content.

DOE-STD-1070-94

DOE-HDBK-1118-99, GUIDE TO GOOD PRACTICES FOR CONTINUING

TRAINING, which provides information and guidance for the development and

implementation of a continuing training program. This guide will assist in meeting

Objective 5, Design and Development of Training Programs, and Objective 8,

Training Program Evaluation; specifically Criterion 5.4, 8.4, and 8.5.

DOE-HDBK-1119-99, GUIDE TO GOOD PRACTICES FOR THE SELECTION,

TRAINING, AND QUALIFICATION OF SHIFT SUPERVISORS, which provides

guidance for the design and development of shift supervisor training programs. This

guide will assist in meeting Objective 4, Determination of Training Program Content.

2.2 Non-Government Documents. The following non-government publications were

used in the development of this document.

IAEA-TECHNICAL REPORT SERIES No. 380, NUCLEAR POWER PLANT PERSONNEL

TRAINING AND ITS EVALUATION – A GUIDEBOOK, which provides guidance for the

systematic approach to training issued by the International Atomic Energy Agency, Vienna,

Austria.

DOE-STD-1070-94 APPENDIX

This Page Intentionally Blank

DOE-STD-1070-94 APPENDIX

DEFINITIONS

All key terms used in this standard are defined in DOE O 426.2, which is referenced in

Section 2, Applicable Documents.

INTRODUCTION

In recent years the Department of Energy (DOE) has given increased attention to the

improvement of DOE nuclear facility operations. Internal and external reviews of DOE activities

(e.g., National Academy of Sciences reviews, Technical Safety Appraisals, Tiger Team

Assessments, Defense Nuclear Facility Safety Board reviews) have confirmed the need for this

increased attention. These reviews have identified a need for improvement of DOE nuclear

facility personnel training programs, strengthening DOE's role in training, and improved

methods for the evaluation of DOE contractor training programs.

This standard initiates a framework for consistent, systematic evaluation of DOE nuclear facility

training programs through the establishment and use of a uniform set of training program

evaluation objectives and criteria. The performance objectives and criteria contained in the

Appendix to this standard shall be used by DOE Headquarters and field organizations for the

evaluation of nuclear facility training and qualification programs. DOE contractors should also

use these objectives and criteria to perform internal training program evaluations to determine

strengths and weaknesses and to form the basis for improvement action plans. Evaluations

conducted in accordance with this standard should consider prior commitments or action items

in implementation plans for DOE Orders or resulting from previous internal and external

evaluations.

THE EVALUATION PROCESS

5.1 Benefits of Evaluations. Evaluations of training programs are conducted to

provide reasonable assurance that programs are producing competent employees who are

capable of performing their jobs safely and efficiently. This assurance benefits the Department

through increased productivity, increased worker and facility safety, and decreased costs of

operation.

DOE-STD-1070-94 APPENDIX

Training and qualification programs require a significant investment in equipment, materials,

and personnel resources. Evaluations of a training program's effectiveness in producing

competent employees are conducted to ensure that training is being conducted in a

consistent, cost effective, and efficient manner. Other reasons for training program

evaluations include the need to determine:



program strengths and weaknesses;



if worker performance has improved;



if program content matches current job needs; and



if corrective actions are needed to improve program effectiveness.

This standard provides objectives and criteria that promote consistent evaluations and

therefore comparable results. For many years, evaluations of DOE training programs have

been conducted by various organizations and the results have not always been comparable

primarily because either different criteria were used as the basis for each evaluation or the

criteria that was used was unknown by the organization being evaluated. As a result, DOE

Management and Operating contractors have been tasked with resolving findings and

recommendations generated by these evaluations that, at times, were contradictory or

untraceable to existing requirements. A major benefit of using the objectives and criteria in this

standard is consistent evaluations, which will result in greater efficiency and consistency when

improvements to training programs are implemented.

5.2 Evaluator Qualifications. DOE field organizations should establish

implementing procedures for the evaluation of nuclear facility training and qualification

programs. The implementing procedures should include standards for evaluator technical

qualifications and clearly define responsibilities for the preparation, conduct, reporting, and

tracking of training program evaluations. The field organization should establish a schedule

for evaluating nuclear facility training programs that is consistent with DOE orders and

directives.

DOE-STD-1070-94 APPENDIX

The DOE organization (Headquarters or field) responsible for conducting evaluations should

select the evaluator(s) using selection criteria that will maximize credibility, bring expertise to

bear where needed, and increase the likelihood of fresh solutions to problems through new

perspectives. Selection, training, and qualification requirements for personnel performing

evaluations of technical training and qualification programs should be developed and

promulgated in ancillary documents.

Each evaluator's experience should be commensurate with individually assigned objectives and

criteria. Before beginning the evaluation the evaluator(s) should be trained in evaluation

methodology, and should be familiar with the objectives and criteria which they are assigned to

evaluate. The training program objectives and criteria contained herein are not a substitute for

the evaluator's technical knowledge of the facility or program. The evaluation shall be

performed using personnel who have a technical background (e.g., nuclear facility operations,

maintenance, and radiological protection personnel, and/or expertise in tritium, plutonium, or

other subjects) in the subject area(s) being evaluated. If a group of individuals are performing

the evaluation, the team should be made up of an appropriate balance of personnel with

training and technical backgrounds. The optimum situation is to use personnel with a technical

background and experience in training design, development, and management. If the

evaluation is conducted by someone who does not have the specific technical qualifications,

the results should be reviewed by a subject matter expert with expertise in the subject area(s)

before it is forwarded to the Management and Operating contractor.

5.3 Evaluation Methods. The objectives and criteria (Appendix A) may be used

individually by a person or collectively by a team to evaluate a specific objective or criterion or

as a package to evaluate the entire training program. The objectives and criteria were designed

to accommodate either the single person approach or the team approach. Job aids (i.e.,

checklists and forms) that can be used by either a person or by a team to support training

program evaluation will be developed and published separately.

Training program evaluations should be conducted through observation of the overall program

and they should answer the question: "Does the training program meet the objectives and

criteria contained in this standard?" The following resources should be used when conducting

training program evaluations:

DOE-STD-1070-94 APPENDIX

 Facility policies, procedures, program descriptions, and records;

 Training materials, such as lesson plans, guides, student handouts, and tests; and

 Cognizant facility personnel.

Evaluations should be conducted at the facility, at the training center, and at other locations

where training activities occur. Evaluations should center around three major activities to

determine the extent to which training programs are meeting the objectives and criteria.

These activities include observation of training, personnel interviews, and document reviews.

Observation of training should focus on the people (both instructors and trainees), the

instructional environment, and the instructional process. The key steps involved in the

observation of training are:

 Select the training to be observed, obtain a copy of the lesson plan or guide, and

review it prior to the observation;

 Explain the purpose of the observation to the instructor and attend training (do not

participate in the discussion and minimize trainee attention to the observation);

 Take detailed notes during the observation and write only facts;

 Compare the facts observed with the desired behaviors or conditions; and

 Note any strengths and/or weaknesses.

Interviews require a different set of skills to acquire information about training. Successful

interviewing is dependent on communication skills, both speaking and listening, and on good

questioning techniques. Key considerations during the interviewing process include:

DOE-STD-1070-94 APPENDIX

 Pre-Interview Activities -- decide on goals for the interview, determine the key

personnel who would provide the most complete and accurate information, and

develop a set of questions in advance.

 Interview Activities -- explain the interview purpose and answer any questions the

interviewee may have, use open-ended questions to obtain detailed information, use

closed questions to obtain short answer conclusions, assess throughout the interview,

express appreciation for interviewee's time, and restate the purpose of the interview at

its conclusion.

 Post-Interview Activities -- compare responses to the objectives and criteria, and

assess once again whether the information provided helped to accomplish the

original goal(s) of the interview.

Training records should be reviewed to verify that materials and activities are being properly

documented, processed, and retained. Program-level records include task lists, lesson plans,

instructor qualifications, and program evaluations. Trainee-level records include attendance

records, test results, qualification cards, and certifications. When inconsistencies exist, further

investigation should be conducted to determine the depth of the problem. Assess the system

as a whole. Are the records properly validated and entered into the system in a timely manner?

Is there an effective document control system? Are all the records in the system and are they

readily retrievable?

5.4 Evaluation Frequency. Training program evaluations using the objectives and

criteria specified in the Appendix should be conducted as part of the DOE field organization

environment, safety, and health appraisal program and contractor internal review program.

Training program evaluations should also be conducted by both the DOE field organization

and the contractor when significant changes occur in training needs, personnel performance

deficiencies are noted, or indicators show a significant performance degradation. Training

program evaluations should be conducted every three years to determine the effectiveness

and efficiency of the training system in providing a knowledgeable and skilled workforce to

support safe and efficient facility operations. The evaluation can consist of one overall

evaluation or a series of topical evaluations conducted over the three year period.

DOE-STD-1070-94 APPENDIX

In addition to performing overall or topical training program evaluations, DOE field

organizations should perform day-to-day evaluation of technical training and qualification

activities. This includes activities such as monitoring classroom and on-the-job training (OJT)

sessions, spot-checking training materials and individual training and qualification records,

monitoring oral examinations, and reviewing examination results. The detail and frequency of

the day-to-day evaluation activities is dependent upon the hazard, risk, and complexity

associated with the operation of the facility.

5.5 Graded Approach. The graded approach shall be considered when applying the

criteria to a training program or activity. For example, the requirements and the level of detail

and structure associated with establishing a systematic approach to training (SAT) should be

consistent with the hazard potential and the complexity of the facility. Alternative approaches

are acceptable and encouraged to streamline all phases of the systematic approach to training.

Regardless of the approaches used to establish training programs, a strong evaluation

process is essential to ensure effective implementation and regular improvements. When

applying the objectives and criteria, evaluators should recognize that training programs for

low-hazard nuclear facilities generally do not need to be as detailed as training programs for

higher-hazard nuclear facilities. The evaluator should apply the objectives and criteria with

consideration of the level of detail that has been set forth in facility policies and agreed to by

DOE management. The DOE Handbook, Alternative Systematic Approaches to Training,

provides additional guidance on alternative implementation methods.

6. APPLICATION OF OBJECTIVES AND CRITERIA

The objectives and criteria (Appendix) describe the expected results of an effective,

well-managed training program. The objectives address:

 Management and administration of training and qualification programs;

 Development and qualification of training staff;

DOE-STD-1070-94 APPENDIX

 Trainee entry-level requirements;

 Determination of training program content;

 Design and development of training programs;

 Conduct of training;

 Trainee examinations and evaluations; and

 Training program evaluation.

The criteria are principles or methods that support the objectives and are to be applied with

judgment. The expectation is that all objectives will be met. However, some criteria may not be

applicable to some programs. This situation would prevail when, for example, a particular

method such as laboratory training is not used. The evaluator shall choose the objective and

associated criteria to accomplish the scope of the assessment that is to be performed. The

method chosen to meet the objectives and criteria is determined by the contractor.

The amplifying statements associated with the criteria provide guidance to the evaluator in

areas such as personnel to interview, documents to review, and standards to look for in

determining if the criteria are satisfied. The amplifying statements are not meant to be all

inclusive. The evaluator may need to look for methods not mentioned in the guidance to verify

meeting the criteria. The DOE standards referenced in section 2.1.2 contain additional guidance

that can be used. Conversely, not all of the items listed in the guidance may be necessary to

meet a criterion. Considering the graded approach, some facilities may satisfactorily achieve

criteria without considering all of the review guidance.

The evaluators shall use their knowledge of the facility's policies and procedures to determine

whether or not a specific criterion or review guidance is applicable to the training program being

reviewed. The determination of applicability is a DOE management (e.g., field program or

training office) responsibility.

DOE-STD-1070-94 APPENDIX

7. REPORTING EVALUATION RESULTS

As stated previously, evaluations can be conducted as a comprehensive evaluation or as a

series of topical evaluations. Therefore, the evaluation report may address a single objective or

criterion (topical) or may be comprehensive depending on the type of evaluation conducted.

The topical approach may be used over a period of time to evaluate the entire program. If this

method is used, a report should be written for each segment of the evaluation. In this case,

individual reports should be combined into a comprehensive report that addresses the entire

program at the completion of all individual segments. This comprehensive report should include

a section that draws conclusions from the results of the individual reports relative to the overall

effectiveness of the entire training program.

As training program reviews are being performed, the evaluator should record field notes. In

most cases these are briefly written notes that can be referred to at a later time. These notes

do not have to contain a long narrative description of what is, or is not, being accomplished in

support of the criteria. When all of the information related to the review has been obtained, the

evaluator should document the results. The problem, reason, example, proposal (PREP)

method is an effective means for recording findings. The evaluator(s) document a concern with

the training program by briefly stating the problem, explaining the reason why it is a problem,

giving specific examples of the problem's existence, and providing a proposal or

recommendation for resolving the problem. Upon completion of the data gathering phase of

the evaluation, the evaluator(s) should review all of the information and develop an evaluation

report. A differentiation should be made in the evaluation report between a finding that

requires specific corrective action and a finding that identifies a program strength or

noteworthy practice. Programs or activities that are positive examples of effective training

programs or methods or which are considered noteworthy should be made available to other

DOE facilities, as appropriate.

There are several characteristics of an effective report that should be considered regardless

of whether the single segment or total program evaluation approach is used. However, the

person(s) writing the evaluation report should follow locally prescribed procedures or policies

when compiling the report. Incorporating these characteristics into a report increases the

probability that the report will be understood. An effective report shall be organized, factual,

DOE-STD-1070-94 APPENDIX

complete, objective, accurate, and should provide contractor management with findings and

recommendations. The report should be reviewed with contractor management for factual

accuracy prior to issuance. Findings and recommendations should be reported to contractor

management in a timely manner. Any safety violations observed during the evaluation shall

be reported to contractor management immediately. The following is an example of the type

of information that should be included in evaluation reports.

 Cover page -- The cover page includes the report title, the evaluator(s) name(s), and

the period of time over which the evaluation was conducted.

 Summary/Abstract -- An abstract explains the kind of information that is included in the

evaluation report. Typical content would be the areas evaluated, purpose of the

evaluation, and major findings and recommendations.

 Historical background regarding the program -- The depth of this section depends solely

on the audience. For example, if the intended audience is unfamiliar with the program

concerned, it is beneficial to provide a more comprehensive background. If the intended

audience is familiar with the content of the program, the information should be brief and

to the point. Regardless of the intended audience, the report should include the goals,

objectives, and critical components of the program.

 Description of the evaluation -- This section introduces the strategy employed for the

evaluation. It addresses three major areas, which include: 1) the purpose of the

evaluation, 2) how the evaluation was conducted, and 3) the key personnel involved in

the evaluation.

 Results and recommendations -- This section conveys the results of the evaluation and

the proposal or recommendation for resolution. Before writing this section, all the

information should be tabulated and analyzed. A clear explanation of the data improves

the clarity and credibility of the report. It is vitally important to explain what the data

actually mean. Often this is the section that is referred to most often; therefore, it should

be prepared with detail and care. This section should list each objective and criterion in

order, indicate whether the objectives and criteria were met, and describe any reasons

for not meeting the objectives or criteria.

DOE-STD-1070-94 APPENDIX

 Conclusions -- This section contains a group of statements based on the evidence or

observed findings. This section should also highlight noteworthy practices that are

identified during the evaluation. It should reflect the purpose and objective of the

evaluation.

8. TRACKING EVALUATION RESULTS

The DOE field organization should ensure that a formal process is in place to document the

results of training evaluations, provide those results to contractor management, and track and

monitor the successful completion of corrective actions to remedy deficiencies.

Recommendations should be referenced to specific criterion or other regulations or

requirements, and should be clearly communicated to the contractor. Contractor management

should submit a written corrective action plan to the DOE organization responsible for the

training program that was evaluated. This corrective action plan should address the schedule

and actions that will be taken to resolve recommendations.

The responsible DOE organization(s) should review the corrective action plan to ensure that it

adequately addresses the recommendations. Acceptance of corrective action plans should be

formally communicated to the contractor. The DOE field organization should monitor progress

and verify completion of all action items.

DOE-STD-1070-94

APPENDIX

OBJECTIVES AND CRITERIA

DOE-STD-1070-94 APPENDIX

This Page Intentionally Blank

DOE-STD-1070-94 APPENDIX

MANAGEMENT AND ADMINISTRATION OF TRAINING AND

QUALIFICATION PROGRAMS

OBJECTIVE 1

The facility is organized, staffed, and managed to facilitate planning, directing, evaluating,

and controlling a systematic training process that supports the facility mission(s).

Criteria

1.1 Facility line management has overall responsibility and authority for the content

and effective conduct of the training and qualification program(s).

Line management ownership, commitment, and accountability are the foundation for

the training and qualification programs at the facility. Line management is responsible

for ensuring that these programs will produce competent workers and supervisors.

The commitment to the training of personnel at the facility includes participation of

line management in all phases of the training program. Management ensures that

resources are available to support the training effort, mandates attendance at training

sessions, and is thoroughly knowledgeable of all aspects of the training and

qualification program(s) in which that facility's personnel participate.

Management-approved policies and procedures are implemented that promote a

systematic approach to training. They adequately describe the duties,

responsibilities, and authorities of line and training management, and detail the

interfaces involved in implementing the training and qualification programs for both

training staff and facility personnel. They also describe the process for the analysis,

design, development, implementation, and evaluation of the training programs.

DOE-STD-1070-94 APPENDIX

1.2 An organization/person within line management is responsible for the

implementation of the training and qualification program(s).

A training group is established as part of the line organization. If a training group is not

separately established, then personnel within the line organization are assigned

responsibilities for implementing the training and qualification program(s). At facilities

with small staffs and/or training programs, the training group may consist of only one

individual, either full- or part-time. However, the job function, responsibilities, authority,

and accountability of personnel involved in managing, supervising, and/or implementing

training are clearly defined in the incumbent's job description, procedure, or similar

document.

1.3 Goals, objectives, and plans are in place to describe the implementation of the

training and qualification programs.

Written goals and objectives related to the implementation of the training and

qualification processes are in place and stated in documents such as strategic plans,

award fee criteria, policies, and mission statements. The goals and objectives

adequately address the current issues that are important to both contractor

management and DOE. Facility line management and the training organization

implement specific plans as appropriate to ensure adequate management of the

training program.

1.4 Training records are maintained to support management information

needs and to provide required historical data.

Training records are maintained in an auditable manner. Training records support

management information needs and provide required data on each individual's

training participation, performance, and qualification/certification. Training records

are also maintained to support verification of the accuracy of training program

content.

DOE-STD-1070-94 APPENDIX

1.5 Training developed and/or implemented by personnel or organizations other than

the operating contractor's staff is monitored and controlled to ensure that it

meets applicable facility requirements.

Training provided by an outside organization (e.g., sub-contractor, vendor, site

central training) in support of the qualification or certification of facility personnel

meets the same basic requirements for development, implementation, testing, and

documentation as training provided by the facility staff.

1.6 Training facilities, equipment, and materials effectively support training activities.

Adequate facilities are available to support safe and consistent training. Sufficient

facilities and proper tools, equipment, and materials are available to support

applicable training content and performance activities (e.g., hands-on training for

maintenance personnel and technicians). Instructional support materials and

equipment such as audio-visual equipment, flip charts, and marker boards are

adequate to support the training activities. In addition to facilities to support the

implementation of training, staff facilities and equipment are available to support

analysis, design, development, and evaluation of training. Technical reference

materials such as procedures, technical manuals, and drawings are readily

available to instructors and trainees on all shifts.

DOE-STD-1070-94 APPENDIX

This Page Intentionally Blank

DOE-STD-1070-94 APPENDIX

DEVELOPMENT AND QUALIFICATION OF TRAINING STAFF

OBJECTIVE 2

Training staff (contractor and subcontractor) possess the technical knowledge, experience,

and the developmental and instructional skills required to fulfill their assigned duties.

Criteria

2.1 The training staff has maintained the education, experience, and technical

qualifications for their respective positions.

Instructors have the technical qualifications, including theory, practical knowledge, and

experience for the subject matter that they are assigned to teach. Methods are

implemented to ensure that individual instructors meet and maintain instructional and

technical position qualification requirements. Developmental and instructional

qualifications of instructors include theory, practical knowledge, and work experience in

analyzing, designing, developing, conducting, and evaluating training, as appropriate to

their job assignments.

2.2 A training program is implemented to ensure that training staff gain the

knowledge and skills required for their position.

A training program is in place to develop the necessary instructor capabilities to fulfill

training program requirements in all applicable training settings. Training staff and

instructors who have not met the qualifications required for an assignment are under

the supervision and guidance of a qualified individual. Subject matter experts used

occasionally as instructors are provided assistance and are periodically monitored. The

instructional skills training program is conducted using approved instructional materials

that are based on learning objectives derived from job performance requirements and

which provide for effective and consistent presentations.

DOE-STD-1070-94 APPENDIX

2.3 A continuing instructional skills training program is implemented to maintain,

improve, and update the knowledge and skills of incumbent training staff based,

in part, on the results of instructor evaluations.

Continuing training includes improvements needed in technical and instructional

knowledge and skills, the correction of identified instructional deficiencies, and

training on new methods and equipment.

DOE-STD-1070-94 APPENDIX

TRAINEE ENTRY-LEVEL REQUIREMENTS

OBJECTIVE 3

Trainees meet the minimum requirements for entry into the training program.

Criteria

3.1 Entry-level requirements are established for each position and include, as

applicable, the minimum education, experience, technical, and medical

requirements.

Procedures or policies describe the personnel selection and entry-level requirements.

Line management, working with Human Resources personnel, identify the entry-level

criteria for personnel working in a particular operating organization and/or assigned to

specific duties or tasks. Entry-level requirements address the minimum physical

attributes a trainee should possess, as well as the minimum educational, technical, and

experience requirements necessary for the employee to meet job requirements.

3.2 Personnel selected for and/or assigned to the operating organization meet the

prescribed entry-level requirements prior to being assigned to a position.

Line management is responsible for the hiring or transfer of personnel into positions

for which entry-level requirements are established. Applicable education, experience,

technical, and medical requirements are verified and documented for personnel who

are required to meet entry-level requirements.

3.3 Training program entry-level requirements are reviewed and revised as necessary

on the basis of evaluation of trainee performance.

Entry-level requirements for a training program are reviewed as part of the overall

evaluation process. Entry-level requirements are at the proper level to ensure that

personnel can achieve the established learning objectives at the completion of training.

Individual training course prerequisites are also established and reviewed periodically.

DOE-STD-1070-94 APPENDIX

This Page Intentionally Blank

DOE-STD-1070-94 APPENDIX

DETERMINATION OF TRAINING PROGRAM CONTENT

OBJECTIVE 4

Program content for competent job performance is identified, documented, and included in

the training programs, as appropriate.

Criteria

4.1 The tasks required for competent job performance are identified and documented

through a systematic analysis of job requirements. The training program is based

on the results of this analysis.

A systematic analysis of job requirements is conducted to provide reasonable assurance

that all tasks that are essential to safe and efficient operation are addressed by the

training program. Subject matter experts, line management, and training staff develop

and maintain a valid facility-specific task list as the basis for the training program. The

facility-specific list of tasks selected for training is reviewed periodically and updated as

necessary by changes in procedures, facility systems/equipment, job scope, and

advances in technology.

4.2 Current facility safety analysis report, procedures, technical and professional

references, DOE Guidelines and Orders, and industry operating experience are

referenced as applicable to establish both initial and continuing training.

DOE and other appropriate training guidelines are used as a guide for selecting,

sequencing, and verifying training program structure and content. Current facility safety

analysis report, operating procedures, technical and professional references, and

facility/industry operating experience are used to identify facility specific training

content and information for use in developing training materials.

DOE-STD-1070-94 APPENDIX

4.3 Training for Technical Staff personnel is based on an assessment of position

duties and responsibilities.

A detailed analysis is not necessary to determine training program content for technical

staff personnel. Consensus-based content guides (i.e., Best Practices), broad-based

assessments of training needs, and regulatory requirements can be used to assist with

the determination of training program content.

This method may also be sufficient to determine training program content for

positions at many low-hazard nuclear facilities.

DOE-STD-1070-94 APPENDIX

DESIGN AND DEVELOPMENT OF TRAINING PROGRAMS

OBJECTIVE 5

Training program materials identify and support the knowledge and skills needed by trainees

to perform tasks associated with the position for which training is being conducted. The

content of initial training prepares the trainee to perform the job for which the candidate is

being trained. The content of continuing training maintains and improves incumbent job

performance.

Criteria

5.1 Learning objectives are derived from tasks selected for training. Learning

objectives describe knowledge and skills required for successful job performance

and are specified in observable and measurable terms.

Learning objectives are written to reflect task performance and consider the

associated knowledge and skills. Training settings are considered when writing

learning objectives. Learning objectives include the actions the trainee should

demonstrate, conditions under which the action will take place, and standards of

performance. The minimum trainee entry-level knowledge, skills, and experience

for the position are considered when developing learning objectives. If conditions

and standards for knowledge and/or skill objectives are implied, they should be

clearly understood.

DOE-STD-1070-94 APPENDIX

5.2 Lesson plans and other training materials used in the selected training setting

(e.g., classroom, laboratory, simulator, individualized instruction, on-the-job

training, etc.) are accurate, support the learning objectives, and promote effective

delivery of training.

Lesson plans are developed or modified using learning objectives derived from job

performance requirements. The content of lesson plans and other training materials

adequately addresses the learning objectives. The lesson plans contain sufficient

detail to ensure consistent and repeatable training. Information contained in the

lesson plans is sufficient to ensure that personnel are trained to a level required and

expected by facility management.

Lesson plans or equivalent training guides are used for laboratory training, on-the-job

training, and simulator training and include standards for evaluating trainee

performance. Training materials for these non-classroom training settings provide for

effective and consistent instruction. The training materials provide sufficient information

to guide the trainee and the instructor in the performance of the task.

The training materials used to guide discussions with technical staff trainees

normally are not in lesson plan format; rather training materials include key

points that support the learning objectives, taking into account the job position

and the experience of the designated instructor. This approach may also be

sufficient for much of the training that is conducted at low-hazard nuclear

facilities.

5.3 Review, approval, and control requirements are established and utilized for all

training materials.

Subject matter experts and training management review and concur on training

materials. The cognizant line manager approves them prior to use. Training materials

are controlled in a manner that ensures that the latest approved version of the material

is used.

DOE-STD-1070-94 APPENDIX

5.4 A continuing training program is in place and maintains and improves the

knowledge and skills of job incumbents.

Continuing training content includes refresher training on overtrain tasks, facility and

industry events, facility and procedure modifications, retraining addressing task

performance deficiencies, and training on infrequently performed tasks.

DOE-STD-1070-94 APPENDIX

This Page Intentionally Blank

DOE-STD-1070-94 APPENDIX

CONDUCT OF TRAINING

OBJECTIVE 6

Training is conducted in the setting most suitable for the particular training content. Training

is consistently and effectively presented using approved lesson plans and other training

guides.

Criteria

6.1 Training is conducted using approved and current training materials.

Lesson plans that meet criterion 5.2 are used to deliver training. Training in all

settings is sequenced effectively to provide completion of prerequisite knowledge

and skills prior to receiving training on more advanced knowledge and skills.

Individualized instruction, when used, provides the trainees with sufficient guidance

and supporting materials for achieving the learning objectives.

6.2 Training replicates actual job conditions to the extent practical, and allows for

direct participation by the trainees.

Instructors use the references, tools, equipment, and conditions of task performance

that reflect actual job conditions to the extent practicable. Trainee demonstration of

task performance is evaluated on actual plant equipment whenever feasible.

6.3 On-the-job training is conducted and evaluated by designated personnel who

have been instructed in program standards and methods.

Line management implements standards and policies pertaining to the conduct of on-

the-job training (OJT). Personnel who are designated by line management and are

trained in the instructional techniques peculiar to OJT conduct and evaluate it. OJT is

conducted using valid methods, approved materials, and a planned and logical

instructional sequence. Part time OJT instructors and/or evaluators are trained in OJT

instructional methods.

DOE-STD-1070-94 APPENDIX

Completion of OJT and task qualification is by actual task performance whenever

possible. When the task cannot be performed, but is simulated or walked-through, the

conditions of task performance, references, tools, and equipment reflect actual

performance of the task to the extent feasible. Task performance evaluation is

conducted using valid methods and consists of evaluating trainee performance using

established standards prior to task or job qualification.

Structured on-the-job familiarization is normally used in lieu of formal on-the-job

training and evaluation for managers, non-certified supervisors, and technical staff.

During this phase, the candidate works closely with supervisors and managers in their

day-to-day job functions, including decision-making.

6.4 Laboratory training is effectively and consistently presented.

Laboratory training provides hands-on application of principles conveyed during the

classroom training and encourages analytical skills development. The training

program content is implemented as outlined by approved training materials and is

structured to provide practical experience. Laboratory training activities encourage

direct trainee participation in the learning process. Conditions of task performance,

references, tools, and equipment reflect actual job performance requirements to the

extent possible. Evaluation of trainee performance verifies that the trainee has

obtained the essential knowledge and performance skills associated with the job.

6.5 Simulator training is effectively and consistently presented, where appropriate.

Training on a facility control room or process simulator is used to build operating team

skills and/or enhance the effectiveness of hands-on skill training. An appropriate

simulator is used for hands-on training to demonstrate operational characteristics and

for recognition and control of normal, abnormal, and emergency facility/process

conditions. Differences between the simulator and the facility/process are

accommodated in the training session.

DOE-STD-1070-94 APPENDIX

TRAINEE EXAMINATIONS AND EVALUATIONS

OBJECTIVE 7

Individual trainees are examined and/or evaluated on a consistent and regular basis to ensure

that learning is taking place and that trainees are acquiring the knowledge and skills required to

work efficiently and safely at their jobs.

Criteria

7.1 Trainees are evaluated regularly using written, oral, and/or performance

examinations and quizzes.

Trainees are evaluated on a regular basis. Examinations/evaluations are administered at

the conclusion of structured segments of the training program. A sufficient sampling of

the knowledge and skill learning objectives is evaluated prior to awarding qualification or

certification.

Much of the training for managers, non-certified supervisors, and technical staff

personnel occurs in nontraditional settings such as discussions with individual

managers. Monitoring and evaluating training in these nontraditional settings are

unnecessary. In addition, since many learning objectives for managers, non-certified

supervisors, and technical staff personnel do not readily adapt to prescribed standards

or quantitative testing, qualitative evaluations are acceptable in many cases. For

example, trainees’ qualification could be assessed from responses during discussions,

behavior during role-playing, or material developed during training exercises.

Qualitative evaluations may also be used to assess trainee qualification at low-hazard

nuclear facilities.

DOE-STD-1070-94 APPENDIX

7.2 Examinations (both written and oral) and OJT, laboratory, or simulator

performance evaluations are based on learning objectives, administered

consistently, controlled, and documented.

Test items are reviewed by subject matter experts for technical content, meaning,

and correct answer. The results of the review process are documented.

Examination questions are at the proper depth and detail to ensure adequate

evaluation of the trainees' knowledge and skills. Examinations and performance

evaluations contain a representative cross-section of knowledge, skills, and

abilities required for the position. All examination questions relate to one or more

learning objectives.

The acceptance criteria used to grade examinations and performance evaluations

are defined in advance of the examination or performance evaluation.

7.3 The content of written and oral examinations is changed at intervals sufficient

to prevent compromise.

A policy or procedure is implemented to provide direction for how often and how

much examinations are changed to prevent compromise. Examination changes

may be based on how often the course of instruction is used and whether the test

data is controlled or shared with the trainees as a part of the learning process.

7.4 Development, approval, security, administration, and maintenance of written

and oral examinations, and performance evaluations are formally controlled.

A procedure or policy is implemented that controls the development, approval,

security, administration, and maintenance of all types of examinations. Access to

examinations is physically controlled and limited to designated personnel.

DOE-STD-1070-94 APPENDIX

7.5 Remedial training and reevaluation are provided when examination or

performance standards are not met.

Remedial training programs are provided as necessary to prepare the trainee to

meet the identified training program entry-level requirements for areas where

he/she may be deficient. In cases where a trainee fails an examination, remedial

training is based upon the weaknesses identified in the examination. Remedial

training plans are specified in advance, acknowledged by the trainee and approved

by supervision. Completion of remedial training is documented.

DOE-STD-1070-94 APPENDIX

This Page Intentionally Blank

DOE-STD-1070-94 APPENDIX

TRAINING PROGRAM EVALUATION

OBJECTIVE 8

A systematic evaluation of training effectiveness and its relation to on-the-job performance is

used to ensure that the training program conveys all required skills and knowledge.

Criteria

8.1 A comprehensive evaluation of individual training programs is conducted by

qualified individuals on a periodic basis to identify program strengths and

weaknesses.

A policy or procedure describes the long- and short-term requirements for performing

program evaluations and provides guidance relative to who does the evaluation, how

often evaluations are conducted, and how evaluations are conducted. The results of

training program evaluations, including program strengths and weaknesses, are

identified, documented, and used as a basis for training program revision on a periodic

basis.

8.2 Instructional skills and technical competencies of instructors are evaluated

regularly.

Instructors are evaluated regularly in all settings in which they instruct by training

management, line organization supervision, and peers. The instructors are evaluated

against an established set of criteria and the results are used to improve performance.

DOE-STD-1070-94 APPENDIX

8.3 Feedback from trainee performance during training is used to evaluate and refine

the training program. Feedback from former trainees and their supervisors is used

to evaluate and refine the training program.

Examination results (written and performance) are analyzed to determine

weaknesses in the development or delivery of instruction. Changes to the program

content and/or design are made as appropriate. After the trainee has had an

opportunity to use the information gained during training, feedback from the trainee

and his/her supervisor is used to determine the effectiveness of training.

Improvements to the program are based in part on collective trainee/supervisor input

as to how well the trainee can perform the tasks for which he/she was trained.

8.4 Change actions (e.g., procedure changes, equipment changes, facility-specific

and operating experience) are monitored and evaluated for their applicability to

initial and continuing training programs and are incorporated in a timely manner.

Changes in job scope are evaluated to determine the need for revision of initial

and continuing training programs.

Changes that impact training program accuracy are incorporated into the training

program in a timely manner and training is provided as necessary to inform facility

personnel of changes that have an impact on facility operation. Clear responsibility is

assigned for providing facility modification and procedure change information to the

training organization.

8.5 Improvements and changes to initial and continuing training are systematically

initiated, evaluated, tracked, and incorporated to correct training deficiencies and

performance problems.

A policy or procedure identifies the requirements and provides the guidance for

documenting, evaluating, tracking, and incorporating changes to training programs.

Data from criteria 8.1, 8.3, and 8.4 evaluations form the basis for making program

improvements and modifications.

DOE-STD-1070-94 APPENDIX

8.6 Training materials are maintained current, based upon the results of training

program evaluations.

A procedure or policy is developed and implemented that describes the process for

revising and documenting training material updates based upon the results of training

program evaluation.

8.7 Training facilities are evaluated to determine their effect on the training process.

Training facilities are evaluated to determine if they are conducive to the learning

process. Classrooms and training settings are free from excessive disturbances and

distractions. Trainees have adequate space to work and learn individually and in

groups, as appropriate. Conditions related to comfort (e.g., heat, lighting, noise level,

desk space, etc.) meet standards for good learning environments. The training staff's

office and working spaces are adequate to support the training being developed and

presented.

DOE-STD-1070-94

APPENDIX

This Page Intentionally Blank

DOE-STD-1070-94 APPENDIX

CONCLUDING MATERIAL

Review Activity: Preparing Activity:

DOE Operations Offices DOE-HS-32

AD AL

BPA CH Project Number:

CE FN 6910-0043

DP ID

EH NV

EM OR

ER RL

FE SF

GC SR

IG National Laboratories

NE ANL

RW BNL

SA FNAL

WAPA INEL

LBL

LANL

LLNL

NREL

ORNL

PNL

SNL