HOME APPLIANCES
LUDP8908SN
LG SIGNATURE Dishwasher
IM P O R TA NT
QUICK INSTALL & CLEARANCES
For full installation directions/clearances please refer to
the corresponding User Manual and Installation Guide.
PRODUCT DIMENSIONS
© 2018 LG Electronics USA, Inc. All rights reserved. “LG Life’s Good” is a registered trademark of LG Corp. All other product and brand names are trademarks or registered trademarks of their respective owners. Design, features and specifications are
subject to change without notice. Non-metric w
eights and measurements ar
e appro
ximat
e. Some featur
es may r
equire Internet ac
cess. Cont
ent and services ma
y vary b
y product and ar
e
subject to change without notice. 12/
4/20
DIMENSIONS
A Width 23 3/4"
B Height 33 3/5"
C Depth 24 3/5"
D Depth with Door Closed with Handle (in) 24 3/5"
E Depth with Door Open (in) 50 1/2"
Carton Dimensions (in) (W x H x D) 28” x 34 7/10” x 29 3/5”
POWER RATINGS
ENERGY STAR
®
Qualified Yes
CEE Tier 1
Energy Use (kWh/Year) 269 kWh/Year
Water Factor (WF) 2.8
CERTIFICATIONS
NSF
®
Certified Yes
•
Operate this appliance with the correct voltage as shown in your User Manual
and on the rating plat
e. Connect it t
o a dedicated, pr
operly grounded br
anch
circuit which is protected by a time delay fuse. Connect the appliance using
3-wires, including a ground wire.
•
If an outlet and other power
connector are used, it should
be in an accessible location
dishwasher and within 4 ft
(1.2 m) of the dishwasher’s side.
•
The wiring must be grounded
properly. If in doubt, have
it checked by a qualified
other appliance to the same
outlet.
•
Route the wiring.
•
Make sure the electrical cable is
▲
! WARNING
•
For personal safety, remove house
fuse or open circuit breaker before installation.
•
Do not use an extension cable or adapter with this dishwasher
NOTE:
•
If you find any damage to the dishwasher, contact your retailer or contractor.
PREPARING ELECTRICAL WIRING
PREPARING WATER SUPPLY CONNECTION
Make sure the house water supply is turned off before connecting the
dishwasher water lines.
•
Connect the dishwasher to
a hot water supply with a
temperature range between
120°F (49°C) and 149°F
(65°C). This temperature
range provides the best
washing results and shortest
cycle time. To prevent
damage to dishes, the
temperature should not
exceed 149 °F (65°C).
•
When connecting the
dishwasher water line,
sealing tape or compound
should be used on pipe
threads to avoid leaks. Tape
or compound should not
be used on compression
fittings.
•
The water supply tube must be located in the left side channel.
NOTE:
•
If you find any damage to the dishwasher, contact your retailer or contractor.
Back view
A
B
Side view
C
D
E
Water supply hose, drain hose and electric
cable should be passed through this area.
PREPARING CABINET OPENING
24" (610 mm) min.
33 /2" (851 mm) min.
1
24" (610 mm) min.
This dishwasher is designed to fit a standard dishwasher opening.
An opening may be needed on both sides to route
•
Select a location as close to the sink as
possible for easy connections to water and
drain lines.
•
To ensure proper drainage, install the
dishwasher no more than 12 ft. (3.65 m)
from the sink.
•
If installing the dishwasher in a corner, leave
a minimum of 2” (50 mm) between the
dishwasher and the adjacent wall.
•
To allow for proper clearance of plumbing
and electrical, use the template included
with the literature to determine the
clearance on the side of the cabinet where
2 1/2” diameter hole saw, drill a hole in the
target area as shown on the template.
•
For flush installations only, you may remove
the cabinet brace inside the cabinet.
▲
! WARNING
•
Don’t use existing holes unless they are in the target area. Otherwise, the
water supply and drain hose may be damaged by being crushed or kinked.
▲
! CAUTION
•
Failure to properly locate the hole for the water and drain lines may prevent
kinked or damaged lines. Installation damage is not covered by the warranty,
and leaks caused by improper installation may result in property damage.