zt elite 60 - zero-turn mower

For additional information, please see us at

www.badboymowers.com

Bad Boy, Inc.

102 Industrial Drive

Batesville, Arkansas 72501

ZT ELITE

ZERO-TURN MOWER

OWNER’S, SERVICE & PARTS MAN

UAL

TABLE OF CONTENTS

PAGE 2

Basic Information

Bad Boy Safety Guidelines

Operation

Maintenance

Storage and Transportation

Troubleshooting and FAQ

Controls

Moving In-operable Mower

Instrumentation

Mower Blade Maintenance

Greasing Bearings

How To Choose the Right Blade

Mowing Tips

Service Section

Parts Section

Limited Warranty

Page 4

Page 5

Page 9

Page 10

Page 12

Page 13

Page 14

Page 15

Page 16

Page 17

Page 18

Page 19

Page 37

Page 54

Section 1

Section 2

Section 3

Section 4

Section 5

Section 6

Section 7

Section 8

Section 9

Section 10

Section 11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PAGE 3

This manual applies to the following equipment:

Bad Boy ZT Elite Series

ZT 6000 60˝ KT745 Kohler

COMMONLY USED ITEMS AND PART NUMBERS

ZT Hydraulic filter

60" ZT Deck Belt

ZT Pump Belt

Fuel Filter

Spark Plug

Oil Filter

Motor Oil

Hydraulic Oil

60" ZT Blade

063-5002-00

063-5003-00

063-5004-00

10W-30 Motor Oil - Bad Boy Synthetic Blend Motor Oil Recommended

20W-50 Motor Oil - Bad Boy Hydrostatic Oil Recommended (Approximatley 2.5 Quarts per Transaxle)

Air Filter

063-1050-00

041-1650-00

041-6400-00

063-5001-00

015-8000-00

Gator Blade Wave Blade

Hi-lift Fusion Blade

038-6060-00

038-6003-00 038-6016-00

Pre-cleaner

SECTION 1: BASIC INFORMATION

Congratulations on the purchase of your new Bad Boy Mower! The purpose of this manual is to assist

operators in maintaining and operating their machine. The information and instructions in this manual can

help you attain years of performance from your new Bad Boy. Also, check out our website to learn more

about the Bad Boy family.

All Bad Boy engines use 10W-30 engine oil. For maximum protection, Bad Boy synthetic

blend engine oil is recommended.

All Bad Boy hydraulic systems use 20W-50 engine oil (Conventional or Synthetic). Bad Boy

Hydrostatic oil is recommended.

All Bad Boy Mowers use hi-temp multi-purpose grease. NLGI No. 2 for the grease fittings.

ZT models have 12 psi in both front and rear tires.

Most Kohler engines hold approximately two (2) quarts of motor oil. Be careful not to over fill engine oil.

Refer to the engine’s service manual.

Warranty Registration

The Warranty Registration form must be completed within 30 days to validate your warranty. As the new

equipment owner, you are expected to see that the form is completed and forwarded to Bad Boy, Inc.,

at time of delivery. Warranty is non transferable. Warranty registration should be completed by the

selling dealership using the on-line registration site.

Model/Serial Number

Your ZT model serial numbers are found on the SIN plate underneath seat. These numbers can assist you

in the ordering of new parts when replacements become necessary.

arts/Service

Only Bad Boy replacement parts are to be used on your mower.

Replacement parts are available through your local Bad Boy Mower Dealer. Remember to always provide

the following information when ordering parts:

1. Correct part number

2. Correct serial number

All warranty repair and service must be handled through your authorized Bad Boy Mowers dealer.

To locate the nearest dealer, go to our website and click on Locate a Dealer.

PAGE 4

1.1

1.2

1.3

1.4

1.5

PAGE 5

SECTION 2: MOWER SAFETY GUIDELINES

Never allow untrained people to operate this machine. It is the owner’s responsibility to get training and see to it that anyone who has

permission to use your machine receives the proper training. Do not mow around people. The factory discharge chute is designed

to deflect debris downward, but it could be possible for debris to be thrown in a way that can cause damage to people or property.

Seek additional training when possible to learn more about safety techniques and practices. This cutting machine is capable of

amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result

in serious injury or death.

GENERAL OPERATION

2.1 Read, understand, and follow all instructions on the machine and in the manual before starting.

2.2 Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times.

2.3 Always remain seated while operating the machine. If the machine is equipped with Roll Over Protection (ROPs), always buckle

your seat belt.

2.4 Only allow responsible adults who are familiar with the instructions to operate this machine.

2.5 Clear the area of objects such as rocks, wire, toys, etc., which could be thrown by the blades.

2.6 Always maintain a safe distance from people and pets just prior to, and during, operation. Stop the machine if anyone enters the area.

2.7 Never carry passengers.

2.8 Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.

2.9 Never direct discharged material toward anyone. Avoid discharging material against a wall or obstruction as material may

ricochet back toward the operator. Stop the blades when crossing gravel surfaces.

2.10 Never operate the machine without the discharge chute, grass catcher, or other safety devices correctly in place and functioning

properly.

2.11 Slow down before turning.

2.12 Always disengage blades, place steering controls in neutral, engage parking brake, and remove ignition key when leaving

operators seat. Never leave a running machine unattended.

2.13 Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the

machine, inspecting the machine for damage, removing the grass catcher, or unclogging the discharge guard.

2.14 Always operate machine in daylight or with adequate working lights.

2.15 Do not operate the machine while under the influence of alcohol or drugs.

2.16 Watch for traffic when operating near or crossing roadways.

2.17 Always wear eye protection when operating or servicing the machine.

2.18 Always wear ear protection, such as earplugs, while mowing.

2.19 Use extra care when loading or unloading the machine into a trailer or truck.

2.20 Be alert of surroundings. Watch for rocks, stumps, mounds, depressions, and low hanging limbs or objects that could be

potentially hazardous while mowing.

2.21 Data indicates that operators 60 years of age and above are involved in a large percentage of riding mower related injuries.

These operators should periodically evaluate their ability to operate the riding mower safely enough to protect themselves and

others from serious injury.

PAGE 6

SLOPE OPERATION

Slopes are a major factor related to loss of control and tip over accidents, which can result in severe injury or death. Operation on all

slopes requires extra caution. If you cannot back up the slope, or you feel uneasy on it, do not mow it.

2.22 Mow up and down slopes, not across.

2.23 Watch for holes, ruts, bumps, rocks, or other hidden objects that tall grass can obscure. Uneven terrain could overturn the machine.

2.24 Choose a low ground speed when operating the machine on a slope.

2.25 Do not mow on wet grass, the tires may lose traction.

2.26 Do not attempt to coast down a slope in the neutral position.

2.27 Avoid starting, stopping, or turning on a slope. If the tires lose traction, disengage the blades and proceed slowly, straight

down the slope.

2.28 Keep all movement on slopes slow and gradual. Sudden changes in speed or direction could cause the machine to roll over.

2.29 Use extra care while operating machine with grass catchers or other attachments: they can affect the stability of the machine.

Do not use on steep slopes.

2.30 Do not try to stabilize the machine by putting your foot on the ground.

2.31 Do not mow near drop offs, ditches or embankments. The machine could suddenly roll over if a wheel goes over the edge or

the edge caves in.

2.32 Be aware of what is located at the bottom of slopes. For example: rocks, water, cliffs, and roadways.

CHILDREN

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the

mowing activity. NEVER assume that children will remain where you last saw them.

2.33 Keep children out of the mowing area and in the watchful care of a responsible adult other that the operator.

2.34 Maintain alertness and turn machine off if a child enters the area.

2.35 Before and while backing, look behind and down for small children.

2.36 Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere

with safe machine operation. Children who have been given rides in the past may suddenly appear in the

mowing area for another ride and be run over or backed over by the machine.

2.37 Never allow children to operate the machine.

2.38 Never leave key in the ignition, especially around children.

2.39 Use extreme care when approaching blind corners, shrubs, trees, or other objects that may block your view

of a child.

TOWING

2.40 Tow only with a machine that has a hitch specifically designed for towing. Do not attach towed equipment except at the hitch

point.

2.41 Follow the manufacturer’s recommendation for weight limits for towed equipment and towing on slopes.

2.42 Never allow children or others in or on towed equipment.

2.43 On slopes, the weight of the towed equipment may cause loss of traction and loss of control.

PAGE 7

SERVICE:

SAFE HANDLING OF GASOLINE

avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors

are explosive.

2.46 Extinguish all cigarettes, cigars, pipes, and all other sources of ignition.

2.47 Use only an approved gasoline container.

2.48 Never remove gas cap or add fuel with the engine running.

2.49 Allow engine to cool before refueling.

2.50 Never fuel the machine indoors.

2.51 Do not store machine near open flame or source of ignition, such as a water heater or furnace.

2.52 Remove gas powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such

equipment with a portable container, rather than from a gasoline dispenser nozzle.

2.53 Never fill gasoline containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the

ground away from your vehicle before filling.

2.54 Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until the fueling is complete. Do not

use a nozzle lock-open device.

2.55 If fuel is spilled on clothing, change clothing immediately.

2.56 Never overfill fuel tank. Replace gas cap and tighten securely. Tank is full when level reaches bottom of fill tube.

GENERAL SERVICE

2.57 Never operate machine in a closed area where dangerous carbon monoxide fumes can collect.

2.58 Keep all nuts and bolts tight to be sure the equipment is in safe working condition. Never operate a poorly maintained machine.

2.59 Do not touch hot areas of the machine.

2.60 Never interfere with the intended function of a safety device or reduce the protection provided by a safety device. Check their

proper operation regularly.

2.61 Keep the entire machine free of grass, leaves, or other debris build up. Clean up oil or fuel spillage and remove any fuel soaked

debris. Failure to do so can affect the safety and functionality of the machine, as well as increase the danger of a fire due to

contact with the hot surfaces of the machine.

2.62 Allow machine to cool before storing.

2.63 If you strike something with the mower, turn the mower and blades off, engage the parking brake, and inspect the machine for

damage. Repair, if necessary, before resuming.

2.64

Never make any adjustments or repairs with the engine running.

2.65

Check grass catcher components and the discharge guard frequently and replace with manufacturer’s recommended parts,

when necessary.

SETTING DECK HEIGHT

2.44 If your machine is equipped with an actuator motor, raise the deck using the raise /lower switch. Refer to section 7 (Controls).

When deck is raised, set desired height with the deck height control dial, then lower deck with the raise / lower switch.

2.45 If your machine is equipped with a foot pedal, press foot pedal to raise deck, select your desired deck height with the deck

height dial, then slowly release foot pedal.

PAGE 8

2.70

Always maintain the correct tire pressure. Do not inflate the tires above the recommended pressure. Never weld or heat a wheel

and tire assembly. The heat can cause an increase in air pressure resulting in a tire explosion. Welding can structurally weaken

or deform the wheel.

2.71

Park machine on level ground. Never allow untrained personnel to service machine. Understand service procedure before

doing work.

2.72

With the parking brake engaged, bring lever arms to their inward position, then attempt to start the machine (the blade actuator

should be in off position); the engine should not start.

2.73

On a level surface, disengage the parking brake and place lever arms to their outward position, then attempt to start the

machine (the blade actuator should be in off position); the engine should not start.

2.74 Engage parking brake and leave lever arms in outward position, put blade actuator in the on position, then attempt to start the

machine; the engine should not start.

2.75

Next, start the engine as stated in the “Mower Operation Section”, disengage parking brake, and Very Slowly begin to rise from

the seat; the engine should stop.

If any of these tests fail to produce the results indicated and the problem cannot be identified, contact your Bad Boy Mower

dealer or the support contacts in the rear of this manual.

ROLL OVER PROTECTION STRUCTURES (ROPS)

This machine is not equipped with ROPS from the factory. If ROPS are added as an option, it is vital that the rules below are

adhered to. ROPS, when used correctly, dramatically decrease the fatality rate in roll-over instances.

2.76

Periodically ensure the bolts that attach the ROPS to the machine are securely fastened.

2.77

Always operate the machine with the ROPS secured in the upright position.

2.78

If the surrounding environment (e.g. low lying limbs, signage, etc.) makes it impossible to mow with the ROPS upright, lower

the ROPS at the hinge point, mow the area, then immediately secure the ROPS upright.

2.79

Upright ROPS are taller than then operators head. Be aware of this and your surrounding environment, as referenced above.

The mower and operator may clear low lying items, but the ROPS may not.

2.80

Always wear the provided seat belt when ROPS are utilized. Failure to use the seat belt severely handicaps the safety benefits

of the ROPS.

2.81

In the event of a roll-over, replace the ROPS before resuming use of the machine.

2.66 Mower blades are sharp. Wrap the blade or wear gloves before servicing them.

2.67 Check parking brake operation frequently. Adjust and service as required.

2.68

Maintain or replace safety and instruction labels, as necessary.

2.69

Do not attempt to mount a tire without the proper equipment and experience to perform the job.

SAFETY INTERLOCK SYSTEM

Your Bad Boy mower is equipped with a safety interlock system. This system is designed to prevent serious injury or death to the

operator and other people or property damage. The system consists of an o

perator presence switch in the seat, the parking brake,

drive lever neutral position, the mower blade engagement switch, and the ignition switch.

These interlocks are vitally important and must be tested frequently. Following are instructions to test these very important safety

precautions. Note: the operator must be seated properly on the machine during these tests and the engine should

have been previously allowed to warm to operating temperature.

PAGE 9

SECTION 3: MOWER OPERATION

Never operate the machine with faulty equipment. Always be alert of sudden changes in landscape, as

the mower will react differently on slopes or embankments than it will on flat surfaces. Never operate

the mower with the discharge chute open. Do not cross terrain, other than grass, with blades turning.

This could cause damage to property or bystanders.

3.1 Place parking brake in up position

3.2 Drive arms must be in the “open” position. While sitting on the machine, each arm is

positioned away from the operator, to the right and left. Drive arms will lock into place and

must be in this position to start machine.

3.3 Put PTO switch in the "OFF" position.

3.4 If your machine has been equipped with a ROPS (Roll Over Protection System) then you

must fasten seatbelt.

3.5 If machine has not been started recently, engage the choke.

3.6 Make sure nothing is under or around machine.

3.7 Place key in ignition and turn.

3.8 Once machine is started, disengage the choke.

3.9 Increase RPM by sliding the throttle to fast position, toward the rabbit.

3.10 Owners must become familiar with the controls before operating a zero-turn radius vehicle.

3.11 Start slowly and build your skill level. Have ample practice before using the machine at full

capabilities.

3.12 Be comfortable with machine before engaging blades. Know what each component controls

before using machine.

3.13 Your mower will perform differently on an incline /decline. Be cautious, slow down, and do

not make any sudden jerking movements with control arms. The machine could lose traction

on a decline or tip backwards on an incline.

3.14 Once you become comfortable with your Bad Boy Mower you will notice your overall mowing

time will decrease.

Avoid operating your mower on side hills of over 5 degrees,

inclines of over 10 degrees,

and declines of over 15 degrees.

PAGE 10

SECTION 4: MOWER MAINTENANCE

First Every 50 Every 100 Every

Daily 8 Hours or Hours or 250 Section

Maintenance Hours Annually* Annually* Hours

Check and add engine oil ● Section 3

Section 2

(Pump) 6

(Deck)

Check condition of blades ● Section 6

Check for fuel and oil leakage ● Section 3

Initial oil change ● Section 3

Change engine oil and filter ● Section 3

Tighten nuts and screws ●

Grease mower ● Section 5

Replace fuel filter◊

● Section 3

Change Hydraulic oil and filter ● Section 1

Clean combustion chamber

Dealer

●

* Maintenance by hour or annually which ever come first

◊

Check air and fuel filter more often in dust conditions

Dealer Get maintenance performed at a registered dealership

Section 4

Section 3

Section 1●

●

●Check battery terminal connections

Initial change of hydraulic oil and

filter

Replace air element and pre-cleaner

◊

Clean or replace spark plugs and set

gap

Check and adjust valve clearance

Dealer

Clean and lap valve seating surface

Dealer

Interval

●

Check all belts for proper alignment

Check tire pressure and wheel lug

nuts

Section 5

PAGE 11

Performed:

Performed

Performed:

Date: Hours:

MAINTENANCE LOG

Date: Hours:

PAGE 12

SECTION 5: MOWER STORAGE & TRANSPORTATION

5.1 Keep machine from collecting debris by storing in a covered area while not in use.

5.2 Fuel can harm your machine if left for more than 30 days without changing, especially if the

fuel contains ethanol. Never use fuel with more than 10% ethanol by volume. E-15 is not

permitted.

5.3 Disconnect the negative battery cable when machine will be stored for more than 30 days.

5.4 Always secure machine properly when transporting machine.

5.5 Do not load machine on trailer with blades engaged.

5.6 Do not use ramps to load the machine.

5.7 Make sure Parking Brake is in “up” position.

5.8 In wet conditions tires may spin while loading / unloading. If necessary, wait for dry

conditions before loading / unloading.

5.9 Make sure mode of transportation is suitable to bear the weight of mower.

5.10 Deck height should be set at maximum before attempting to load.

5.11 Secure mower with at least two straps capable of securing weight of mower.

PAGE 13

SECTION 6: TROUBLESHOOTING

6.1 Q: How do I prevent an uneven cutting pattern and increase the quality of cut?

6.1 A: Check tire pressure, check blade sharpness (replace blades or sharpen at least once

per year or when needed), make sure blades are tightened properly, check spring and belt

tension, check the underside of the deck to ensure the mower deck is free of grass build-up

and debris, make sure your machine is at full throttle, and vary your mowing pattern each

time you cut your grass.

6.2 Q: What should I do if my mower won’t start?

6.2 A: Check battery charge and connection (grounds), check your fuel (make sure fuel is less

than 30 days old and contains no water), make sure your spark plug is in good condition

and spark plug wire is attached, and make sure air filter is clean (a dirty filter makes it more

difficult for the engine to draw air). Check the integrity of the 25 amp main fuse; also check

for any bare wires and/or bad connections.

6.3 Q: What should I do if the blades won’t engage?

6.3 A: Make sure the safety switch is plugged in on the bottom of seat. Check the underside

of the PTO engager to ensure the plug is secure at switch. Also check PTO fuse underneath

operator console (10amps)

6.4 Q: What type of fuel is recommended for my mower?

6.4 A: We recommend that you use a name brand fuel to ensure quality. Use fuel with an octane

rating near 87. Higher octane fuels offer no benefit. By law, E-15 fuel is not permitted. Usage

of E-15 will result in premature engine failure.

6.5 Q: Do you offer touch-up paint for your mowers?

6.5 A: Touch-up paint is available. Contact your local dealer for more information.

6.6 Q: How durable is the electric deck lift?

6.6 A: The actuator which controls the deck height is designed for moving loads of up to 1000

pounds and has a static holding capability which exceeds 3,000 pounds. Our ¼˝ deck weighs

approximately 250 pounds which is only 25% of working capability. If deck lift will not

operate, check fuse located underneath operator console (15amp).

6.7

How do I clean my mower?

6.7

A: It is recommended that you use an air hose or blower to remove dust and debris from

the

mower, to ensure there is not a build up of grass on the mower deck and engine

compartment, which could become a fire hazard. If you must wash the mower,

ensure you run the engine to operating temp to dry water and engage the blades to

spin off any standing water on the pulleys. Avoid spraying water onto electrical

components and bearings, to prevent premature failure of these parts.

PAGE 14

SECTION 7: CONTROLS

7.1 Ignition Switch—Bad Boy mowers have a three position ignition switch: off, run, and start.

With key inserted, rotate it clockwise to START position and release key when engine starts,

and switch will automatically return to the RUN position.

7.2 Throttle Control—A cable is connected to the engine throttle for controlling engine speed.

Move lever forward to increase engine rpm, move lever backward to decrease engine rpm.

7.3 Choke Control—(Not pictured, located on left side by hand brake) When the lever is in the

down position, the choke is in the off (run) position. When the lever is pulled up, the choke is

in the on (start) position. Do not operate the machine in the on (start) position.

7.4 Control Levers—These levers control the mower’s speed, direction, and neutral lock. These

levers are used to steer, accelerate, decelerate and change direction. (Drive Arms)

7.5 Blade Engage Switch—This switch engages the blades. Pull the switch up to engage the

blades and push the switch down to disengage the blades.

7.6 Deck Lift Control—The deck lift switch is used to raise and lower the deck.

7.7

Deck Height Control—The deck height dial is used to set the cut of the deck.

7.5

7.6

7. 2

7. 7

7.4

7. 1

PAGE 15

SECTION 8: MOVING INOPERABLE MOWER

8.1 Do not tow machine. Use a winch to load on a trailer for transporting.

8.2

8.3

ZT Models are equipped with two neutral engage/disengage arms, located at the rear of

the mower protruding from the frame and under the muffler. By pulling the arms out, the

mower can be put in a neutral position. Return the arms to the “forward position” for normal

operation.

8.4

Your Bad Boy Mower Weighs: ZT SERIES: 800—850 lbs

*** Weights fluctuate with the addition of accessories.

8.5

As you can see by the weights of the machines, you shouldn’t ever try to push or pull a Bad

Boy Mower by hand. This could cause serious bodily injury.

Hopefully, you’ll never need to use this section of the manual. However, if you do, use

extreme caution when moving machine!

SECTION 9: INSTRUMENTATION

99.1

Electronic Hour Meter—Registers Hour increments up to 9,999.9 total hours. This meter

records the cumulative time the engine is running.

PAGE 16

SECTION 10: MOWER BLADE MAINTENANCE

10.1 Check mower blades after each use. This is essential for maintaining well-groomed turf. Keep

the blades sharp. If a dull blade is used for cutting, the grass will tear rather than cut. This

could damage the grass leaving a brown frayed top on the grass within a few hours. A dull

blade will also require more power from the engine.

10.2 NEVER attempt to straighten a bent blade by heating. NEVER attempt to weld a cracked

blade. The blades can break and cause serious injury or death.

10.3 NEVER work with blades while engine is running or deck clutch is engaged.

10.4 ALWAYS place deck clutch in DISENGAGE position while performing maintenance.

10.5 Use blocks when you MUST work under mower.

10.6 ALWAYS wear thick gloves when handling blades.

10.7 ALWAYS check for blade damage if mower strikes

rocks

branches

, or other objects that c

could

potentially damage the blade.

(REMEMBER: NEVER CHECK BLADE WHILE ENGINE IS

ON!NEVER CHECK BLADES WHILE BLADES ARE

ENGAGED!)

SECTION 11:

EQUIPMENT LUBRICATION

11.1 Park the machine on a level surface and disengage the blade control switch.

11.2 Move the motion control levers outward to the neutral position, engage parking brake, stop

the engine, remove the key, and wait for all moving parts to stop before leaving the operating

position.

11.3 Grease Type: NLGI grade #2 multi-purpose gun grease.

11.4 Clean the grease fittings with a cloth. Scrape any paint off the front of the fitting(s).

11.5 Connect a grease gun to each fitting. Pump grease into the fitting until grease seepage is

observed. Be mindful of over-pressurization. Do not force the lever arm if there is strong

back pressure as this can lead to reduced life of the component(s). Wipe up excess grease.

11.6 Refer to service manual section for grease fitting locations.

PAGE 17

HOW TO CHOOSE THE RIGHT BLADE

Essentially there are only TWO basic styles of mowing blades used or approved for use on our current

products:

1) The standard style of mowing blade is essentially designed for cutting grass and effectively discharging

the clippings out from the deck to fall onto the lawn or to be captured in a grass collection system.

Standard blades are also referred to as “2-in-1” (discharging & bagging ) or “high-lift” blades (because

they are designed to create a higher-lifting airflow).

2) Mulching blades generally have a more curved style surface and frequently include extra cutting

surfaces along the blade edges. These blades may also come in a “+” design (which is actually two

individual blades arranged in a perpendicular fashion to enhance mulching). The “+” blades are usually

found on older style mowers; newer ones utilize blades with more advanced mulching technology.

Mulching blades may also be referred to as “3-in-1” (mulching, discharging & bagging) or “all-purpose”

blades.

Bear in mind that the re-circulating airflow design of 3/1 blades makes them less efficient at discharging

grass clippings than a standard 2/1 blade. As with most all-purpose tools, there is some give and take as

opposed to using a tool designed for a more specific purpose.

If you’re experiencing less-than-desired cutting or discharging performance with a 3/1 blade, you may want

to check into using a 2/1 blade. Conversely, if you’re using a 2/1 blade and want to mulch clippings, you

should see about the availability of mulching blades or a mulching kit.*

The type of blade installed on a new mower is a decision the retailer makes for each model of mower, based

on the expected needs of most customers. If you’re unsure of which blade is on a particular model, inspect

the blade. Blades have part numbers stamped into them. Then compare these part numbers with the unit’s

Operator’s Manual or Parts List.

It is true there are many other styles of blades available. But since we don’t manufacture or recommend

using these other aftermarket styles, we will leave them out of this discussion. Should you want more

information on special application or aftermarket blades, you should contact the companies that make these

products. NOTE: Customers using non-OEM blades do so at their own risk. The use of unapproved (non-

OEM) blades may void any or all of the mower and engine factory warranties.

* MULCHING KITS – These generally consist of mulching blades and a mulching plug (which closes off

the discharge opening to keep the clippings contained under the deck for re-cutting) plus any necessary

hardware for installation. Please check with your parts distributor regarding the contents of a particular

mulching kit.

PAGE 18

MOWING TIPS:

• Mow header strips at the ends of the lawn and around flower beds first. Make them wide enough that you can turn the mower

around in the already mown section. Then mow back and forth between these header strips overlapping each lap by about 1/8 the

width of the mower’s deck.

• Don’t cut your grass too short, particularly cool season grasses. Higher heights usually provide for a deeper root system, looks

better, and is less likely to have weeds invading, particularly crabgrass.

• Don’t remove any more than one third of the grass leaf at any one cutting. If circumstances arise that a lawn gets too tall and you

just have to lop off a bunch to get caught up, bite the bullet and break it down into several mowings to get caught up with 3 or so

days between cuttings.

• NEVER SCALP YOUR LAWN. Scalping severely damages the root system to such a degree that it may die.

• Avoid mowing when the grass is wet or when it’s dark

• Avoid throwing grass clippings into the street and driveway where they can be washed into the sewer system. After mowing, clean

up driveway and walkways.

• When mowing remove only a third with each cutting (except for the first mowing of the season when it’s ok to remove more). You

can safely leave clippings that will quickly decompose and add nutrients back into the soil. Contrary to popular opinion, grass

clippings do not add to thatch buildup. Grass blades are made up of about 75% water.

• Mow your lawn in a different direction with each mowing, especially with lawns of shorter grass types. Altering the direction

ensures a more even cut since grass blades will grow more erect and less likely to develop into a set pattern.

• Keep your mower’s blade sharp, which means having it sharpened several times during the mowing season. Keep several blades

around so you’ll always have a sharp one on hand. Sharp blades cut the grass cleanly and help mulch clippings into small pieces

which break down quickly.

• Don’t forget to change your mower’s oil at least once during the mowing season. For brand new mowers, change the oil after

about 5 hours of operation during the initial break-in period.

• At the end of the mowing season use a fuel stabilizer in the remaining gasoline

• In the spring, don’t use that old gas unless you properly used a fuel stabilizer, it can cause a number of problems. Better to use

fresh gasoline to begin the new mowing season.

• Leaf blade A demonstrates what a leaf blade should look like

after mowing with a sharp blade.

• Leaf blade B demonstrates a leaf blade that was injured by a

dull mower blade.

• Leaf blade C was cut by the mower but indicates that the

mower blade is not sharp enough. The shredded white tissue

protruding from the leaf blades C and D is the vascular tissue

of the plant.

• Leaf blade D has been mown for quite some time with a dull mower blade.

To bag or mulch?

Grass clippings do not contribute to thatch buildup or increase the chances of disease. If you mow your lawn at the right height,

without removing any more than 1/3 of it’s total height, clippings will quickly breakdown without a trace. These clippings

contribute additional nitrogen and other nutrients to the soil and supply it with additional organic materials. Clippings from a

1000 sq. ft. lawn can add as much as 1 - 2 pounds of nitrogen back into the soil.

If you have a compost pile, then you may want to bag your clippings occasionally to add much needed green-matter to the

compost pile. Make sure it is mixed thoroughly with brown matter to avoid a strong ammonia odor. DO NOT COMPOST

CLIPPINGS after applying any weed control or weed-feed type product. Before adding clippings to the compost pile wait at

least 3 mowings after these products have been applied.

PAGE 19

SERVICE SECTION

SECTION 1: HYDROSTATIC SYSTEM

The hydraulic fluid reservoirs are accessed by raising the

seat. Notice the “full cold” line at the bottom of the tank. Use

only 20W-50 motor oil in this tank. (Bad Boy Hydrostatic oil

is recommended)

Changing your hydraulic oil and filter:

1) Remove the tops from the hydraulic fluid

reservoirs and get an oil drain pan. Lifting the

mower from the rear will make access to the

transaxles easier and allow you to purge the air

from the transaxles.

2) Remove the three ¼” filter guard screws and filter

guard from the ZT-3100 Transaxle. Clean any

loose debris from around the perimeter of the

filter.

3) Place the oil drain pan under the oil filter as the

oil filter serves as the drain for the transaxle.

4) After the oil has drained, wipe the filter base

surface off and apply a film of new oil to the

gasket of the new replacement filter.

5) Install the new filter by hand, turn ¾ to one full

turn after the filter gasket contacts the filter base

surface.

6) Re-install the filter guard with three ¼” screws.

Torque screws to 65 in. lbs. (7.3 Nm) each.

7) Repeat steps 1-6 on the opposite side transaxle

drive.

Hydraulic Fluid Reservoirs

PAGE 20

8) Drain old oil filters of all free flowing oil prior to disposal. Place

used oil in appropriate containers and deliver to an approved

recycling collection facility.

9) Remove the top port plug from the left

side and right side transaxles prior to

filling with oil. This will allow the

transaxles to vent during oil fill and

prevent any air lock within the

transaxles.

10) Fill with 20W-50 motor oil (Bad Boy

Hydrostatic oil is recommended) through the

hydraulic fluid reservoirs until it just appears at the bottom of

each transaxle’s top port (approximately 2 quarts per transaxle,

4 quarts total). Install the top port plug into each transaxle as

the oil level reaches this port.

11) Install and torque the top port plugs to 180 in. lbs. (20.3 Nm).

12) Continue to fill the transaxle through the hydraulic fluid

reservoirs until the “Full Cold” line is reached on the hydraulic

fluid reservoirs.

13) Re-install the caps on the hydraulic fluid reservoirs.

14) Now we need to purge the air from the transaxle. With your

mowers tires off the ground disengage the brake and start the

engine.

15) Pull the neutral bypass levers which are located on each side of

the muffler. Then slowly move the drive arms in the forward and

reverse direction 5 to 6 times.

16) Push the neutral bypass levers back into place. Move the drive

arms forward and backward 5 to 6 times slowly. Check the oil

level and add oil as required after stopping the engine.

17) It may be necessary to repeat steps 15 and 16 until all the air is

completely purged from the system. When the transaxle

operates at normal noise levels and moves smoothly forward

and reverse at normal speeds, then the transaxle is considered

purged.

PAGE 21

Under the rear of the mower, you will find the

two levers shown in the image. These bypass

levers serve as a neutral for moving the mower

while the engine is not running. Pull the levers

out and lock them into place to activate the

bypass.

When adjusting the tracking on the mower, the

length of the pushrods can be changed by screwing

the pivot joint in or out on the ends of the rods.

Shortening the overall length of the rod slows the

pump down. Lengthening the rod will increase the

speed of the pump.

Neutral Bars

Right Push Rod

Left Push Rod

PAGE 22

SECTION 2: DRIVE BELT

Shown on the right is a typical pump belt tensioner

for your ZT model mower. Tightening the two ¾

jam nuts on the right side will increase the belt

tension on all models.

The belt tension should be set between 60-65 lbs.

Use a belt tension gauge to ensure the proper

tension. Your dealer or service center will have a

belt tension gauge or you can buy one (Part

Number 041-9999-00).

PAGE 23

SECTION 3: ENGINE

Kohler KT

745

This machine has an oil drain hose installed

on the engine to allow for easier oil changes.

Bad Boy recommends that the oil and filter

be changed after the initial 8 hrs of use, and

at intervals of 50 usage hours or yearly,

whichever occurs first after that. The oil

capacity is 2 quarts. Bad Boy 10W-30

synthetic blend engine oil is recommended

for maximum protection.

3.1 Changing your engine oil and oil filter:

1) Remove oil dipstick and open oil

drain. Allow oil to completely drain.

(Make sure to have an oil pan ready

to capture old oil and properly

dispose old oil.)

2) The oil filter is located on the right

side of the engine. Clean area

around oil filter. Place a container

under the oil filter to capture any oil and remove filter.

Wipe off mounting surface and reinstall drain plug.

Torque to 10 ft. lb.

3) Place new filter in shallow pan with open end up. Fill with

new oil until oil reaches the bottom of the threads. Allow

2 minutes for oil to be absorbed by filter material.

4) Apply a thin film of clean oil to rubber gasket on new filter

5) Refer to instructions on oil filter for proper installation.

Oil Dipstick

Oil Filter

Fuel Filter

Oil Drain

Spark Plugs

Air Filter

PAGE 24

6) Fill crankcase with approximately 2 quarts of new oil.

Level should be at top of indicator on dipstick.

7) Reinstall oil fill/dipstick and tighten securely.

8) Start engine; check for oil leaks. Stop Engine; correct

oil leaks. Recheck oil level.

9) Dispose of used oil and filter in accordance with local

ordinances.

PAGE 25

The fuel filter is located in the fuel line about 12" from the

carburetor on the side of the engine. Replace the filter

yearly. Prior to the removal of the old filter, note the direction

of fuel flow as indicated on the filter. Have towels readily

available in order to quickly remove any fuel leakage.

Always use new hose clamps and ensure the security of the

new filter by lightly pulling on each hose. Always perform

maintenance outdoors or in a well ventilated area. Do not

smoke or allow any open flames in the vicinity of any

maintenance activities.

3.2 Changing your fuel

filter

Locate your fuel filter and mark the direction it is

facing.

Clamp each side of the fuel filter to minimize any

gas spills.

Remove the clips from each side of the fuel filter

and remove the fuel filter.

Place the new fuel filter in the same direction as

the old and place clips back into place and remove

clamps.

PAGE 26

The air cleaner is the engine’s only defense against

damaging foreign particles. It is very important that the

air cleaner element is inspected prior to each use.

Remove the element and tap its sides in order to remove

debris. Do not blow the filter out using compressed air.

Doing so will greatly reduce the air cleaners

effectiveness. Replace yearly; more often in dusty

environments. Adhering to these practices will help

prevent loss of power and premature engine failure.

3.3 Changing the air cleaner:

1) Unlock the air cleaner cover and remove to

access the air cleaner.

2) Remove the paper element and precleaner.

3) Replace or wash precleaner in warm water

with detergent. Rinse and allow to air dry.

4) Lightly oil precleaner with new engine oil;

squeeze out excess oil.

5) Replace paper element and place precleaner

onto new paper element.

6) Install onto base and place cover back on and

lock into place.

PAGE 27

3.4 Changing the spark plugs and checking the spark plug gap:

1) Remove the wire on the spark plug and use a 5/8”

socket to remove the spark plug.

2) Check the gap on the spark plug to verify that it is

0.03 in using a feeler gauge.

3) If the spark plug is worn, overheated, wet or

carbon fouled replace the spark plug.

4) Install the plug into cylinder head and torque to 20

ft.-lbs. Be careful not to overtighten the spark plug.

SECTION 4: ELECTRICAL SYSTEM

This mower is equipped with three protective fuses: a 25

amp main fuse (pictured to the right), a 10 amp clutch fuse

(blade engagement) and a 15 amp linear actuator fuse

(deck lift). The main fuse is located on

the left side of the unit; by the starter solenoid. The clutch

fuse is located just underneath the control panel along

with the linear actuator fuse. You will need to remove the

four screws that hold the control panel to the tank using

a 3mm or a 1/8” hex wrench.

A blown fuse usually indicates a problem within the

electrical system or an electrical component. Ensure the

battery terminals are tightly fastened. Never replace a

fuse with one of a higher amperage rating or

‘bypass’ a fuse in any way. Doing so creates

a significant fire hazard and can cause severe damage to

the mowers electrical components. If a fuse is repeatedly

blowing, contact your Bad Boy dealer.

On most models, the red wire coming out of the engine is

the charging wire from the alternator. Check for 13.6 -

14.2 volts dc at this wire with engine at full throttle.

If you are having issues starting your mower ensure the

signal wire is connected to your starter solenoid.

Use a

3mm

Wrench

Remove

4 Screws

PAGE 28

Check the condition and connection of the relays

located under the control panel. Ensure that they are

clean and connected. Make sure that wire terminal

ends have not been pushed out of the relay block.

The linear actuator is the mechanism that raises and lowers

the deck. If it ever starts to make noise when raising and

lowering the deck you might find it necessary to tighten the

nuts and bolts on the front and rear of the actuator. Be

careful not to overtighten these as you can damage the

actuator. Also if your actuator ever stops working make sure

to check the fuse under the control panel as shown on the

previous page.

Parking Brake Relay

Seat Relay

Starter Relay

Engine Charge Relay

Drive Arms Relay

Front

Actuator

Attachment

DO NOT

OVERTIGHTEN!!!

Rear

Actuator Attachment

DO NOT

OVERTIGHTEN!!!

PAGE 29

PAGE 30

SECTION 5: FRAME

The front fork nuts require a torque of 40ft-lbs. While

applying this torque, turn the fork itself to ensure no damage

is done to the bearing. This operation is only necessary if a

repair requires it. To access the recessed front fork nuts,

remove the dust cap by prying gently using a flat-head

screwdriver. Once cap is removed, a 36mm socket will be

needed for top nut. You will need to secure the bottom nut

with a 1 1/2". wrench. Once you have torqued the nuts to 40

ft.-lbs., reapply the dust cap by gently tapping around its

edges. Do NOT hit center of cap.

Torque rear wheel lugs to 65-75 ft. lbs. Re-torque at every oil

change and check at every mowing.

40 ft lbs

40 ft-lbs

PAGE 31

The pump belt tensioner is located under the engine and

has a grease fitting at its pivot point. Grease at every

engine oil change.

The deck belt tensioner is located at the rear of the deck

and has a grease fitting on its pivot point. Grease at

every engine oil change.

The control arm blocks have grease fittings

located on the top of each block. Grease one

time a year.

Drive Arm Grease Zerk

PAGE 32

SECTION 6: CUTTING DECK

Deck belt removal

1)Remove ignition key.

2) Raise the deck to its highest position.

3) Remove the right pulley cover.

4) While lifting up on the belt (as shown in the

photograph), rotate the pulley until the belt is free of

the pulley. Exercise caution while performing this step

as fingers can easily become caught between the belt

and pulley.

Deck belt installation:

1) Follow steps 1 and 2 from the deck removal section.

2) Take off both pulley covers and route the belt by

following the belt route sticker.

3) The easiest way to finish running the belt is routing the

belt through the deck pulleys and carefully slipping the

belt onto the clutch in the rear of the engine.

4) Verify that the belt is routed properly as improper routing

can damage the spindles as well as the engine.

Remove Pulley Cover

Belt Route

PAGE 33

Leveling the Deck

1) Start on a flat, level surface and set the air

pressure in all four tires to 12 psi.

2) Loosen the four bottom deck hanger bolts using

a 9/16” wrench.

3) Raise the deck as far up as it will go. Place two

2x4s, with 2” side facing up, to create 4” of

space underneath the deck. Make sure the

2x4s are long enough to support both the front

and back of the deck AND are away from deck

wheels. Place a ¼” spacer on each 2x4 under

the REAR of the deck to obtain proper pitch.

4) With the deck still raised, turn the height

adjustment knob to 3.25 and lower deck onto the

2x4s.

5) With deck still on 2x4s, tighten the four deck

hanger bolts while pressing down on the deck to

reduce any slack.

6) Remove 2x4s. Measure all four corners to

ensure deck is now level. The rear should

measure 4” with the front measuring 3 ¾”.

7) Raise the deck up and ensure the height

adjustment knob makes a full rotation. If full

rotation is made, the deck is now level.

PAGE 34

The deck spring tension is critical. If the tension is too

high, premature failure of the deck belt and blade

spindles can occur. If the tension is too low, the belt can

‘jump off’ or slip on the pulleys. This results in reduced

cut quality and early belt failure.

Spring tension adjustments can be made by sliding the

bolt shown above forward or backward in the slot of

the deck. Belt tension should be 65-70 lbs with the

deck at its lowest setting.

Use a belt tension gauge to ensure the proper

tension. Your dealer or service center will have a

belt tension gauge or you can buy one (Part Number

041-9999-00).

Blade Sharpening:

The blade on the top (see photo) was

utilized long after replacement was

required. In addition to a decline in cut

quality, failure to replace a worn or

damaged blade creates a major safety

hazard. Bad Boy recommends that blade

sharpening be performed by a

professional.

PAGE 35

Blade Removal:

To change blades, it may be easier to use a piece of

wood to keep the blade from turning so that the bolt

can be loosened. Use a 15/16” socket and impact

Drill, or a wrench and an extension to gain more

leverage. You might need to put a ¾” wrench on top

of the pulley bolt to keep the blade from spinning.

Bolts used have right-handed threads.

Re-torque the blade bolts to 90-110 lbs.

The blade spindles contain a sealed ball bearing

inside the top and bottom of the spindle. The bearings

are replaceable for a more cost effective repair.

PAGE 36

PAGE 37

PAGE 38

PAGE 39

PAGE 40

PAGE 41

PAGE 42

PAGE 43

PAGE 44

PAGE 45

PAGE 46

PAGE 47

PAGE 48

PAGE 49

PAGE 50

PAGE 51

PAGE 52

PAGE 53

NOTES: __________________________________________________________________

________________________________________________________________________

____

_____________________________________________________________________

_________________________________________________________________________

____

_____________________________________________________________________

_________________________________________________________________________

____

_____________________________________________________________________

_________________________________________________________________________

____

_____________________________________________________________________

____

_____________________________________________________________________

_________________________________________________________________________

2017 LIMITED WARRANTY

FOR

BAD BOY ZT MOWERS

1. WHAT THIS WARRANTY COVERS, AND FOR HOW LONG:

Bad Boy, Inc. will, at its option, repair or replace, without charge, any part covered by the warranty which is found to be defective in material and/or

workmanship within the lesser of two (2) year* or 200 hours after date of sale to the original retail purchaser unless the product is used for rental,

commercial, or industrial purposes in which case there is NO warranty.

The leading edge of the deck shell will be warranted for the entire lifetime of the machine to the original purchaser against defects in materials and

workmanship. Labor required to repair or replace the leading edge of the deck shell will be covered by Bad Boy, Inc for the first year and at the unit

owner’s expense during the balance of the lifetime of the machine.

Belts are warranted for a period of ninety (90) days against materials or workmanship defects.

Seats are warranted for a period of (6) months against material or workmanship defects.

At Bad Boy, Inc.’s request, customer will make the defective part available for inspection by Bad Boy, Inc. and/or return the defective part to

Bad Boy, Inc., transportation charges prepaid.

2. WHAT THIS WARRANTY DOES NOT COVER:

A. This warranty does not cover defects caused by depreciation or damage caused by normal wear, accidents, improper maintenance, improper use or

abuse of the product, alterations, or failure to follow the instruction contained in the Owner’s Manual for operation and maintenance.

B. The customer shall pay any charges for making service calls and/or for transporting the mower to and from the place where the inspection and/or

warranty work is performed.

Bad Boy Inc will not be responsible for the pickup and delivery of a machine for warranty purposes.

C. Engines are warranted separately by their respective manufacturer. The available warranties covering this item are furnished with each mower. Bad

Boy, Inc does not assume any warranty obligation, liability or modification for this item, which is covered exclusively by the stated warranty of the

respective manufacturers.

D. Tires, blades, deck anti-scalping wheels, and dust covers are considered to be consumable wear items and are therefore not warranted.

E. Batteries are warranted for six months (free replacement) from the retail purchase date against materials or workmanship defects. The battery

warranty must be obtained through the battery manufacturer.

F. Normal maintenance services such as oil change, cleaning, lubrication, adjustment.

G. Replacement of services, items, such as oil, lubricants, spark plugs, belts, rubber hoses or other items subject to normal service

replacement.

3. HOW TO OBTAIN SERVICE UNDER THIS WARRANTY:

A. Warranty service can be arranged by contacting the dealer where you purchased the mower. Proof of the date of purchase may be required to

verify warranty coverage. Warranty items must be repaired at an authorized Bad Boy center.

B. Warranty claims will not be reviewed or paid unless the warranty registration is received by Bad Boy, Inc. within 30 days of the retail

purchase date.

C. Warranty claims requiring parts returned will be settled upon return of parts to Bad Boy for inspection.

D. All warranty issues must be handled through an authorized service center or dealership.

4. WARRANTY LIMITATION:

A. THERE IS NO OTHER EXPRESS WARRANTY. ANY WARRANTY THAT MAY BE IMPLIED FROM THIS PURCHASE INCLUDING MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE IS HEREBY LIMITED TO THE DURATION OF THIS WARRANTY AND TO THE EXTENT PERMITTED

BY LAW ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED. Some states do not allow limitations on how long an implied warranty lasts,

so the above limitations may not apply to you.

B. BAD BOY, INC. WILL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, OR SPECIAL DAMAGES AND/OR EXPENSES IN CONNECTION

WITH THE PURCHASE OR USE OF THE MOWER. Some states do not allow the exclusion or limitation of incidental or consequential damages,

so the above limitation(s) or exclusion(s) may not apply to you.

C. Only the warranty expressed in this limited warranty shall apply and no dealer, distributor, or individual is authorized to amend, modify, or

extend this warranty in any way. Accordingly, additional statements such as dealer advertising or presentations, whether oral or written, do not

constitute warranties by Bad boy, Inc., and should not be relied on.

D. This warranty extends only to turf equipment operated under normal conditions and properly serviced and maintained. The warranty expressly

does not cover (i) any defects, damage or deterioration due to normal use, wear and tear, or exposure; (ii) normal maintenance services such

as oil change, cleaning, lubrication, adjustment; (iii) replacement of services, items, such as oil, lubricants, spark plugs, belts, rubber hoses or

other items subject to normal service replacement; (iv) damage or defects arising out of or relating to misuse, neglect, alteration, negligence or

accident; (v) repair or replacement arising from operation of or use of the turf equipment which is not in accordance with operating instructions

as specified in the operator’s manual or other operational instructions provided by Bad Boy Inc.; (vi) repair or replacement arising as a result of

any operation from turf equipment that has been altered or modified so as to, indetermination of Bad Boy, Inc., adversely affect the operation,

performance or durability of the equipment or that has altered, modified or affected the turf equipment so as to change the intended use of the

product; (vii) repair or replacement necessitated by use of parts, accessories or supplies, including gasoline, oil or lubricants, incompatible with

the turf equipment or other than as recommended in the operator’s manual or other operational instructions provided by Bad Boy, Inc.; (viii)

repairs or replacements resulting from parts or accessories which have adversely affected the operation, performance or durability of the turf

equipment; or (ix) damage or defects due to or arising out of repair of turf equipment by person or persons other than an authorized Bad Boy, Inc.,

service dealer or the installation of parts other than genuine Bad Boy, Inc., recommended parts.

As a condition to this warranty, customer shall have read the operator’s manual and ensured the mower has been registered within 30 days

of purchase.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

PAGE 54

PAGE 55

California and Federal Evaporative Emission Control Warranty

Statement

Your Warranty Rights and Obligations

Introduction

The California Air Resources Board (CARB),

the Environmental Protection Agency (EPA) and Bad Boy, Inc.® are

pleased to explain the evaporative emission control system’s warranty on your 2017 model year Large Spark

-Ignited

equipment. In California, and other states, new Large Spark-Ignited equipment that use

off-road Large Spark-Ignited

engines must be designed, built, and equipped to meet stringent anti-smog standards. Bad Boy, Inc.® must warrant

the evaporative emission control system on your Large Spark-Ignited equipment for the

period listed below provided

there has been no abuse, neglect, or improper maintenance of your Large Spark-Ignited equipment. Y

our

evaporative emission control system may include parts such as: carburetors, fuel tanks, fuel lines, fuel caps, valves,

canisters, filters, vapor hoses, clamps, connectors, and other associated emission-related components.

Manufacturer’s Warranty Coverage

The

evaporative emission control system is warranted for two years. If any evaporative emission-related part on

your Large Spark-Ignited equipment is

defective, the part will be repaired or replaced by Bad Boy, Inc.®.

Owner’s Warranty Responsibilities

As the Large Spark-Ignited equipment owner, you are responsible for performance of the required maintenance listed

in your Operator’s Manual. Bad Boy, Inc.® recommends that you retain all receipts covering maintenance on your

Large Spark

-Ignited equipment, but Bad Boy, Inc.® cannot deny warranty solely for the lack of receipts.

As the Large Spark-Ignited equipment owner, you should however be aware that Bad Boy, Inc.® may deny you

warranty coverage if your emission warranty part has failed due to abuse, neglect, improper maintenance, or

unapproved modifications.

You are responsible for presenting your Large Spark-Ignited equipment to a Bad Boy, Inc.® service center as soon

as the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30

days. If you have

a question regarding your warranty coverage, you should contact Bad Boy, Inc.® at

1-870-698-0090, Ext.

6613.

General Evaporative Emissions Warranty Coverage

Bad Boy, Inc.® warrants to the ultimate purchaser and each subsequent purchaser that the Large Spark-Ignited

equipment is:

• Designed, built, and certified to conform with all applicable emissions regulations.

• Identical in

all material respects to the parts as described in the application for certification.

• Free from defects in materials and workmanship that could cause the failure of a warranted part.

he warranty period begins on

the

date

the

Large

Spark

-Ignited

equipment

is delivered to an ultimate purchaser.

The warranted period is two years. Subject to certain conditions and exclusions as stated below, the warranty on

evaporative emissions-related parts is as follows.

PAGE 56

1. Any warranted part that is not scheduled for replacement as required maintenance in the written instructions supplied,

is warranted for the warranty period stated above. If the part fails during the period of warranty coverage, the part will

be repaired or replaced by Bad Boy, Inc.®. Any such part repaired or replaced under warranty will be warranted for the

remainder of the warranty period.

2. Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the

warranty period stated above. Any such part repaired or replaced under the warranty will not reduce the period of

warranty coverage and will be warranted for the remainder of the warranty period.

3. Any warranted part that is scheduled for replacement as required maintenance in the written instructions supplied is

warranted for the period of time prior to the first scheduled replacement date for that part. If the part fails before the first

scheduled replacement, the part must be repaired or replaced by Bad Boy, Inc.®. Any such part repaired or replaced

under warranty will be warranted for the remainder of the period up to the first scheduled replacement point for the

part.

4. Repair or replacement of any warranted part under the warranty provisions herein must be performed at an Authorized

Service Dealer at no charge to the owner.

5. Warranty services or repairs will be provided at all

Service Dealers authorized to service the subject Large Spark-

Ignited equipment.

6. The Large Spark-Ignited equipment owner will not be charged for diagnostic labor that is directly associated with

diagnosis of a defective, emission-related warranted part, provided that such diagnostic work is performed at an

Authorized Service Dealer.

7. Bad Boy, Inc.® is liable for damages to other Large Spark-Ignited engine or Large Spark-Ignited equipment

components proximately caused by a failure under warranty of any warranted part.

8. Throughout the evaporative emission control system’s warranty period stated above, Bad Boy, Inc.® will maintain a

supply of warranted parts sufficient to meet the expected demand for such parts.

9. Manufacturer approved replacement parts may be used in the performance of any warranty maintenance or repairs

and must be provided without charge to the owner. Such use will not reduce the warranty obligations of Bad Boy, Inc.®.

10. Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-

exempted add-on or modified parts will be grounds for disallowing a warranty claim. The manufacturer will not be liable

to warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.

Warranted Parts

The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such coverage if

Bad Boy, Inc.® demonstrates that the Large Spark-Ignited equipment has been abused, neglected, or improperly maintained,

and that such abuse, neglect, or improper maintenance was the direct cause of the need for repair or replacement of the part.

That notwithstanding, any adjustment of a component that has a factory installed, and properly operating, adjustment limiting

device is still eligible for warranty coverage. The following emission warranty parts are covered:

Fuel Line Fuel Line Fittings Control Valves** Fuel Tank Fuel Cap**

Pressure Relief Valves** Control Solenoids**

Vapor Hoses

Clamps** Electronic

Controls** Carbon

Canister

Vacuum Control Diaphragms** Purge Valves

Canister Mounting Brackets

**Note: As they relate to the evaporative control system.

Bad Boy, Inc.

102 Industrial Drive

Batesville, AR 72501

www.badboymowers.com

Technical Support:

............................................................techsupport@badboymowers.com

Warranty: .....................................................................................warrant[email protected]

Parts: ............................................................................................partsdept@badboymowers.com

WARRANTY REGISTRATION

Ensure selling dealership has registered mower within

30 days of purchase to validate warranty.

Please record your serial number, date of purchase and dealership information

for your records.

Serial # ______________________________________________________

Date of Purchase _______________________________________________

Dealer Information ______________________________________________

PAGE 57

MODEL

For additional information, please see us at

www.badboymowers.com

Bad Boy, Inc.

102 Industrial Drive

Batesville, Arkansas 72501